E P 4 Green BAG, E P 1 Orange BAG | Vision Fitness R2750HRT specs

A s s e m b l y G u i d e

R2750HRT

COMMERCIAL FITNESS BIKES

Accessor y

Tray Pedal

Seat Bottom

S T E P 3

PINK BAG

• Mount the upper handlebars to the

console mast using two lock washers

(M8) and two bolts (M8x15L). Tighten

with the 5mm T-Shaped wrench.

• Remove the four mounting screws from

the back of the console. Connect the

wire harness and heart rate wires that

come from the console mast into the

plugs located in the back of the console.

Attach the console to the mast with the

four screws removed earlier.

• Remove the battery cover on the back

side of the console. Plug in the 9-volt

To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.

If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws and bolts are in place and partially threaded in before completely tightening any ONE screw or bolt.

S T E P 6

S T E P 5

battery. Re-attach the battery cover.

S T E P 4 GREEN BAG

• Remove the two socket head bolts

from the sliding seat adjustment bracket.

Slide the seat adjustment handle

between the teeth of the seat adjustment

bracket. Re-insert the two socket head

bolts and tighten with the 4mm L-

shaped wrench.

• Attach the seat frame to the sliding

seat bracket using four lock washers

(M8) and four bolts (M8x20L) and the

5mm T-Shaped wrench.

S T E P 1 ORANGE BAG

•Install the rear foot with the four lock washers (M8), two inside bolts (M8x65L), and two outside bolts (M8x20L). Tighten with the 5mm T-Shaped wrench.

S T E P 2

BLUE BAG

•Slide the console mast boot onto the console mast.

•Unfold the wire harness and heart rate wires located in the console mast frame bracket. Attach the wire tie coming from the bottom of the console mast to the wire harness and heart rate wires. Pull the wire tie with wire harness and heart rate wires up through the top of the console mast while simultaneously sliding the mast into the frame bracket.

•Secure the console mast to the frame bracket with six bolts (M8x15L). Tighten with the 5mm T-Shaped wrench. Insert a set screw (M10x12L) to the front edge of the mast and tighten until snug with the 5mm T-shaped wrench.

•Slide the console mast boot down and snap it into place on the side cover.

S T E P 1

Rear Foot

Console Mast

Boot

Frame

Console Mast

Handlebar

S T E P 3

Seat Handlebar

Wires A

Seat Frame

S T E P 4

• Connect Wires A on the seat

handlebar to Wires B on the sliding

seat bracket. Connect the wire harness

coming from the seat frame to the wire

harness in the handlebars. Attach the

seat handlebars to the sliding seat

bracket using four lock washers (M8)

and four bolts (M8x20L). Tighten with

the 5mm T-Shaped wrench.

S T E P 5 BLACK BAG

•Mount the seat bottom to the seat frame with four bolts (M6x55L) and four lock washers (M6). Tighten with the 4mm L-shaped wrench.

S T E P 6 YELLOW BAG

•Attach the left and right pedals to the left and right crank arms. Tighten the pedals using the 15mm Pedal Wrench.

•Secure the Accessory Tray to the seat handlebar with two bolts (M5x35L) and two lock washers (M5). Be careful when inserting the bolts to clear the wires inside the handlebar to prevent damage. Tighten with the screwdriver.

S T E P 2

Bracket

Wires B

Sliding Seat