Vision Fitness X1500 manual E P 1 Orange BAG

A s s e m b l y	Hand Grips
	S T E P 4
G u i d e	S T E P 3
	Hand Grips

PINK BAG

• Slide the boot onto the console mast.

• Unfold the wire harness located in

the frame bracket. Wrap the end of

the wire tie, located at the bottom of

the console mast, around the end of

the wire harness. Pull the wire tie and

X1500

ELLIPTICAL TRAINER

To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.

If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.

Dual - Action	Dual - Action
Axle Cover
	Arm
Footplate

wire harness up through the console

mast while simultaneously sliding the

mast over the frame bracket.

• Slide a lock washer (SW8)

followed by a flat washer (8x18x1T)

onto four of the bolts (M8x15L). Insert

these bolts through the side of the mast

to secure the mast to the frame. Slide

a lock washer (SW8) followed by a

arc washer (8x17x1T) onto the two

remaining bolts (M8x15L). Insert these

bolts through the holes in front of the

mast. Tighten all bolts with the 5mm

T-shaped wrench.

• Slide the boot down the console mast

and set it in place over the side covers.

• Remove the four bolts from the back

of the console. Connect the wire

harness to the plug in the back of the

console. Connect the heart rate wires

into the heart rate plugs in the back of

S T E P 1 ORANGE BAG

•Slide the stabilizer shaft through the plastic sleeves in the rear support tube. NOTE: A tight fit between the shaft and sleeves is important to the stability of the unit. Because of this, it may be helpful to tap the shaft through with a rubber mallet.

•Slide the stabilizer covers onto the stabilizer shaft and secure with (M8x20L) bolts and (8x16x1T) flat washers. Tighten with the 5mm T-shaped wrench.

•Attach end caps to the end of the guide rails with (M8x15L) bolts. Tighten with the 5mm T-shaped wrench.

S T E P 2 BLUE BAG

•Slide a wavy washer (25x34x2T) on to the right rotation axle. Slide the knuckle joint of the pedal arm assembly onto the right rotation axle. The pedal arm roller wheel should be placed into the groove of the guide rail. Secure the pedal arm assembly to the rotation axle with a washer (8x38x2T) and bolt (M8x20L). Tighten with the 5mm T- shaped wrench.

•Place the pedal arm cover over the knuckle joint. Secure in place with a washer (4x10x1T) and bolt (M4x12L). Tighten with the screwdriver.

•Repeat both steps on the left side.

	Link Arm
S T E P 1	Covers
	S t a b i l i z e r
	S h a f t
	C o n s o l e
	S T E P 4
	S t a b i l i z e r
	C o v e r
End Cap	C o n s o l e
	M a s t
	S T E P 3
	B o o t

Knuckle	Pedal Arm		S T E P 5	CONSOLE
Joint
	Cover
			• Refer to Product Selection and
			Model	Configuration		decal on
Rotation			console or follow these steps.
Axle			• Once the product is plugged in turn
			on the console
			• Select product (Bike (BK) or Elliptical
			(EP)) using the resistance arrow keys.
			Press ENTER to select.
			• Select model number (Bike (1500,
			2050, 2250, 3200) or Elliptical
S T E P 2			(1500, 6000, 6200)) using the
			RESISTANCE		arrow	keys.	Press
			ENTER to select. Console will reset to
		SIMPLE	start-up screen.
Pedal Arm			• The	product	selection and		model
		DELUXE
Assembly
		PREMIER	configuration is now complete.

the console. Attach the console to the

console mast with the four console

bolts and screwdriver.

• Attach the water bottle cage to the

console mast with the two bolts

located on the mast.

GREEN BAG

•Slide the dual-action axle cover into place over the console mast axle. Slide a wavy washer (25x34x2T) onto the console mast axle. Slide the right dual-action arm onto the axle. Fix in place with a washer (8x38x2T) and nylon nut (M8). Cover with the included nylon nut cover.

•Insert the link joint sleeve (SS41) into the socket joint of the right link arm. Position the socket joint of the link arm into the bracket at the bottom of the dual-action arm. Position the Nylon Interval Rings between the socket joint and bracket on each side. Insert a bolt (M8x45L) through the bracket, interval rings and socket joint sleeve. Secure in place with a washer (8x25x1.5T) and nylon nut (M8). Tighten with the 5mm T-shaped wrench and 13mm wrench.

•Position the link arm covers over the socket joint and secure the two pieces together with a screw (M4x12L). Tighten with the screwdriver. Connect the cover to each side of the link arm with a washer (5x10x1T) and bolt (M5x12L). Tighten with the screwdriver.

•Position the right footplate onto the right link arm. Secure in place with four washers (6x14x1T) and four bolts (M5x12L). Tighten with the screwdriver.

•Repeat steps on the left side.

•Attach the hand grips onto the dual- action arms by turning grip in a clockwise direction. Make sure it is tight.

CONSOLES