![](/images/new-backgrounds/1309262/3092623x1.webp)
1Introduction
VISIONTEK GSM Fixed Cellular Terminal 81GF (FCT) with G3 Fax connectivity is a single line PSTN simulation made available from GSM /GPRS network.This gadget performs the task of converting GSM calls to normal analog telephone line with an output similar to existing PSTN environment with all the basic features and additional G3 Fax feature. It provides access to home, office, or any remote location where phone and fax service is needed and GSM footprint is available. Primary telephone fax service, extra lines and security backup are made available thus facilitating outgoing voice and fax calls anytime and anywhere.
VISIONTEK FCT package consists of the following: nGSM FCT – 1 No.
nAntenna – 1 No.
nLine Cord – 2 No. nPower Adaptor – 1 No.
2Installation
SIM Card Installation:
The FCT requires a SIM (Subscriber Identification Module) for its normal operation. SIM socket is provided on the bottom side of the unit.
1.Disconnect power supply if it is already connected to the power socket.
2.Remove the SIM card window by removing the screw.
3.Open the SIM card holder.
4.Ensure for proper direction of the SIM card and insert it gently into the SIM card holder.
5.Close the SIM card holder and press the SIM card holder in forward direction for locking.
6.Fix the SIM card window with the screw.
Antenna Installation:
1.Antenna connector is provided at the rear side of the unit.
2.Connect the antenna supplied with the unit to the connector and ensure for proper contact.
Power Connection:
1.Plug in the primary of adaptor into 230V AC power socket and the secondary to the Power socket (DC 14.2/3A) provided at the rear side of the unit.
2.Connect the battery cable of the Unit to the external battery (12V/5AH). Battery socket is provided at the rear side of the unit. Ensure for proper polarity.
3.Switch ON the unit and observe for the following LED indications on the front panel.
-Red LED indicates the presence of AC power.
-Green LED indicates the presence of Network. LED Blinking indicates the availability of network.
1
Phone Connection
1.Connect the telephone at the RJ11 socket (PHONE) provided at the rear side of the unit.
2.Lift the handset and hear for the dial tone.
FAX CONNECTION:
1.Connect the fax at the RJ11 socket (FAX) provided at the rear side of the unit.
2.Lift the fax handset and hear for the dial tone.
3Operation
Making Calls
1.Lift the handset and hear for the dial tone.
2.Dial the phone number. The dialed number is displayed on the LCD display.
3.After finishing dialing, Press # key on the telephone instrument to send the dialed number. This will avoid the wait time of 7 seconds. Call progressive tone will be heard in receiver till call gets connected.
Receiving Calls
1.The telephone will give a ring on receiving the incoming call.
2.Receiver number is displayed on the LCD display **.
3.Pick up the handset to answer the call.
** Subject to network support
SENDING AND RECEIVING FAX MESSAGES:
The VISIONTEK 81GF FCT terminal allows the connection of group3 fax in the similar way as telephone instrument.
NOTE: (1) The fax communications service has to be activated by the network operator. Otherwise the network will not allow faxes to be sent or received.
(2)You will not be able to make or receive the other voice calls while a fax communications is established.
1.The FCT is programmed to automatically detect the out going calls made by FAX machine.This means the user simply has to use the fax in a same way as a conventional telephone line
2.Incoming faxes are received in the same way as using the fixed line.
2
SENDING FAX MESSAGES:
1.Insert the document into the document feeder.
2.Pick up the handset or press the hands free key on the fax machine.
3.Dial the number of the receiving machine.
4.Wait for the connection. Depending on the setting of the receiving machine, a facsimile reception tone will be heard.
5.Once the fax machine is connected, the fax machine will automatically transmit the document.
RECEIVING FAX MESSAGES:
1.The fax machine will automatically answer the incoming calls.
2.If the fax machine detects fax tones, it begins to receive faxes automatically.
NOTE: (1) For additional information, kindly refer to the user guide of the fax machine.
(2)Use * key to scroll the menus, # to confirm and go
Programming Mode 1
1.In normal mode, the LCD display shows VISIONTEK. On lifting the handset, display shows “PLEASE DIAL”.
2.Press ** and enter the password. Default password is 9999.
Press # key to review the area code entered. Press * key for next menu.
3