VTech 9109 user manual Getting Started, Wall Mounting, Base Unit Features, Handset Features

GETTING STARTED

TELEPHONE

WALL JACK

AC ELECTRICAL

OUTLET

WALL MOUNTING

wooden stud

wallboard

Setting Up Your VT 9109

1.Choose an area near an electrical outlet and a telephone wall jack.

2.Connect the telephone line cord. Insert one end of the telephone line cord into the jack at the rear of the base unit. Plug the other end into a telephone wall jack. Make sure the plugs snap securely into place.

3.Plug the AC power adapter into an electrical outlet and the DC connector to the back of the base unit.

CAUTION:Use only the AC adapter shipped with your VT 9109. This is a Class 2 AC adapter, specifically designed for use with the VT 9109.

NOTE: Connect power to the base unit before placing the handset in the cradle.

4.To select TONE dialing press, MEM/

PROG,**, ,MEM/PROG, To select PULSE dialing press, MEM/PROG,* , # ,MEM/ PROG.

NOTE: Your VT9109 is preset for TONE dialing.

5.CHARGE THE HANDSET BATTERIES BEFORE USE. The batteries recharge automatically whenever the handset is in the base unit cradle. The batteries must be charged for 16 hours before using your phone for the first time.

6.CHECK FOR A DIAL TONE. After the batteries are charged, pick up the handset and press the PHONE key. The IN USE indicator should light up, and

you should hear a dial tone. If not, see

IN CASE OF DIFFICULTY.

CAUTION:

1.Never install telephone wiring during a lightning storm.

2.Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

3.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

4.Use caution when installing or modifying telephone lines.

4

1.Choose a spot near an electrical outlet and a telephone jack.Your phone requires a modular telephone jack and a standard electrical outlet (120V AC). The power cord is six feet long; make sure there is an electrical outlet within reach of the base. The outlet should not be controlled by a wall switch. If the switch is ever turned off, the phone will not operate.

2.Mount the base on the wall. Position the base so the mounting studs will fit into the holes at the back of the base. Position the power cord to extend down the wall the phone is to be mounted on. Slide the base down on the mounting studs until it locks into place.

3.Connect the telephone cord. The telephone line cord has a snap-in plug at each end. Insert one of the plugs into the jack on the bottom of the base. Insert the other end of the plug into the wall jack.

5

4.Connect the power cord. Plug the DC connector into the DC jack at the rear of the base unit. Plug the AC power adapter into an electrical outlet.

BASE UNIT FEATURES

PAGE KEY

* Press the PAGE key to page the

handset.

* Press it a second time to cancel a

page.

* The base will ring the handset 120

seconds before ending the page

automatically.

* PAGE can be cancelled by pressing

PHONE key following by OFF key.

IN USE/CHARGE LED

* The IN USE/CHARGE LED

illuminates steadily when the

HANDSET FEATURES

PHONE LED
PHONE/FLASH KEY	OFF KEY
RINGER SWITCH
	CHAN KEY

TONE/* KEY	REDIAL/PAUSE KEY
MEM/PROG KEY
	VOLUME KEY

handset is in the base cradle to

indicate that the handset battery is

being charged or the handset is off-

6

hook.

CUT

CUT

REPLACEMENT BATTERY ORDER FORM

For VTECH 9109 Cordless Telephone

Name:

Address:

City:

State:

Zip:

daytime phone Number: (

)

ORDER INFORMATION

For Model VT 9109

(QTY.) Batteries @$14.95 each

$

$5.95 Shipping & Handling Per Battery Ordered

$

METHOD OF PAYMENT: DO NOT SEND CASH

CHECK

MONEY ORDER

VISA

MASTERCARD

AMERICAN EXPRESS

CREDIT CARD#

EXP. DATE

CARD HOLDERÕS SIGNATURE

PLACE ORDER FORM AND PAYMENT IN ENVELOPE AND SEND TO:

VTECH COMMUNICATIONS

8770 SW NIMBUS AVENUE

BEAVERTON, OREGON 97008-7195 USA

YOU MAY ALSO ORDER BY PHONE. CALL 1-800-595-9511

PHONE LED

*The PHONE LED lights when the phone line is being used by the handset.

*It flashes with an incoming ring.

*It flashes during PROG mode.

PHONE KEY/ FLASH KEY

*Press the PHONE key to make a call.

*If you are currently on a call, pressing

PHONE flashes the line. This would be used with a feature like call waiting to answer your second call.

CHAN KEY

*Pressing the CHAN key when the handset is in use will activate a channel change to the next free channel.

*This is used if you are experiencing noise or interference on the current

channel.

OFF KEY

*Press the OFF key to exit all modes of operation.

MEM/PROG KEY

*Press the MEM/PROG key to enter MEMORY mode.

*The sequence for dialing out a speed dial number in memory is: PHONE,

MEM/PROG, Number Button (0-9).

RINGER SWITCH

*To turn the ringer switch ON for incomming call alert.

*To turn off ringer move switch to OFF position.

REDIAL/PAUSE KEY

*When you hear the dial tone, pressing the REDIAL/PAUSE key will dial out the last number that was called on your phone.

TONE/KEY

*In PULSE dialing mode, this key is used to switch to Temporary TONE dialing mode.

VOLUME KEY

* There are four volume setting. Press the VOL key repeatedly to cycle from lowest to highest earpiece volume.

BATTERY LOW WARNING BEEP

*Upon pressing PHONE, the Handset will beep to indicate that the battery pack needs to be recharged.

7