VTech VT 30-9116 Getting Started Wall Mounting, Base Unit Features, Handset Features

GETTING STARTED

WALL MOUNTING

AC ELECTRICAL

OUTLET

TELEPHONE

WALL JACK

Setting Up Your VT30- 9116

1.Choose an area near an electrical outlet and a telephone wall jack.

2.Plug the AC power adapter into an electrical outlet and the DC connector to the back of the base unit.

CAUTION:Use only the AC adapter shipped with your VT 30-9116. This is a Class 2 AC adapter, specifically designed for use with the VT30-9116.

NOTE: Connect power to the base unit before placing the handset in the cradle.

the other end into a telephone wall jack. Make sure the plugs snap securely into place.

5.CHECK FOR A DIAL TONE. After the batteries are charged, pick up the handset and press the PHONE key. The PHONE indicator should light up, and you should hear a dial tone. If not, see

IN CASE OF DIFFICULTY.

CAUTION:

1.Never install telephone wiring during a lightning storm.

2.Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

3.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

4.Use caution when installing or modifying telephone lines.

1.Choose a spot near an electrical outlet and a telephone jack.Your phone requires a modular telephone jack and a standard electrical outlet (120V AC). The power cord is six feet long; make sure there is an electrical outlet within reach of the base. The outlet should not be controlled by a wall switch. If the switch is ever turned off, the phone will not operate.

2.Position the wall mount adapter on the base. Line up the tabs on the wall mount adapter with the holes on the bottom of the base. Snap the wall mount adapter firmly in place.

wooden stud

wallboard

3.Mount the base on the wall. Position the base so the mounting studs will fit into the holes on the bottom of the base. Position the power cord to extend down the wall the phone is to be mounted on. Slide the base down on the mounting studs until it locks into place.

4.Connect the telephone cord. The telephone line cord has a snap-in plug at each end. Insert one of the plugs into the jack on the bottom of the base. Insert the other end of the plug into the wall jack.

5.Connect the power cord. Plug the DC connector into the DC jack at the rear of the base unit. Plug the AC power adapter into an electrical outlet.

6.Flip down the wall mount tab on the Base to secure the Handset when cradled.

3.CHARGE THE HANDSET BATTERIES BEFORE USE. The batteries recharge automatically whenever the handset is in the base unit cradle.The batteries must be charged for 24 hours before using your phone for the first time.

4.Connect the telephone line cord. Insert one end of the telephone line cord into the jack at the rear of the base unit. Plug

CHARGING

INUSE

POWER

4

BASE UNIT FEATURES

CHARGING LED

*The CHARGING LED illuminates steadily when the Handset is in the Base cradle to indicate that the Handset battery pack is being charged.

PAGE KEY

5

HANDSET FEATURES

PHONE LED
VOLUME SWITCH	dialpadSM KEY
PHONE KEY
	REDIAL KEY

TONE/*KEY	CHAN/PAUSE KEY
PROG/MEM KEY	FLASH KEY

*Press the PAGE key to page the handset.

*Press it a second time to cancel a page.

*The base will ring the handset 1 min before ending the page automatically.

*The handset can also cancel the page by pressing the PHONE key.

6

CUT

CUT

REPLACEMENT BATTERY ORDER FORM

For VT30-9116 Cordless Telephone

Name:

Address:

City:

State:

Zip:

Daytime Phone Number: (

)

ORDER INFORMATION

For Model VT 30-9116

(QTY.) Batteries @$14.95 each

$

$4.95 Shipping & Handling Per Battery Ordered

$

METHOD OF PAYMENT: DO NOT SEND CASH

CHECK/M.O.

VISA

MASTERCARD

DISCOVER

AMERICAN EXPRESS

CREDIT CARD#

EXP. DATE

CARD HOLDER’S SIGNATURE

PLACE ORDER FORM AND PAYMENT IN ENVELOPE AND SEND TO:

VTECH COMMUNICATIONS 8770 SW NIMBUS AVENUE BEAVERTON, OREGON 97008-7195

YOU MAY ALSO ORDER BY PHONE. CALL 1-800-595-9511

PHONE LED

*The PHONE LED lights when the phone line is being used by the handset.

*It flashes in cadence with an incoming ring.

*It flashes quickly during PROG mode.

*It flashes slowly when battery is low.

*Press the PHONE key to make a call.

*Press the PHONE key again to exit all modes of operation.

dialpadSM KEY

*Press the dialpadSM key to access to dialpadSM service -- No PC or ISP required.

FLASH KEY

* If you are currently on a call, pressing FLASH flashes the line. This would be used with a feature like call waiting to answer your second call.

CHAN KEY

*Pressing the CHAN key when the handset is in use will activate a channel change to the next free channel.

*This is used if you are experiencing

noise or interference on the current channel.

MEM KEY

*Press the MEM key to enter MEMORY mode.

*The sequence for dialing out a speed dial number in memory is: PHONE, MEM,

Number Button (0-9).

PROG KEY

*Press PROG key to enter PROGRAM mode. See Programming Speed Dial Numbers for more details.

REDIAL KEY

*When you hear the dial tone, pressing the REDIAL key will dial the last number that was called on your phone.

PAUSE KEY

*During Speed Dial programming, press PAUSE key to insert a 2 second PAUSE in the dialing sequence.

*It can also be used to store the last number dialed into the speed dial memory. See Storing a Redial Number into Speed Dial for details.

TONE/KEY

* In PULSE dialing mode, this key is used to switch to Temporary TONE dialing mode.

VOLUME SWITCH

*There are three volume settings: Low, Medium and High.

BATTERY LOW WARNING BEEP

*Upon pressing PHONE, the Handset will emit two beeps to indicate that the battery pack needs to be recharged.

7