Waterpik Technologies AquaScape instruction manual Have any questions or need assistance?

Waterpik® AquaScape™

Total Body Showerhead

Pomme de douche Waterpik® AquaScape™

- Aspersion totale

Cabezal de ducha

Waterpik® AquaScape™

Cubre todo el cuerpo

Installation

No tools needed.

Remove old showerhead. Clean pipe threads thoroughly. Hand tighten pivot ball to pipe. To align unit to shower pipe, loosen nut, reposition shower head. Re-tighten nut.

Pipe

Pivot Ball

Nut

Limited Lifetime Warranty

Water Pik, Inc. warrants to the original purchaser of this product that it is free from defects in material and workmanship for as long as the original purchaser owns this product. Water Pik, Inc. will at our election, repair or replace any part of the product which in our opinion is defective, pro- vided that the product has not been abused, misused, altered or dam- aged after purchase. (This includes damage due to use of tools or harsh chemicals.) In the event an item has been discontinued we will replace with what we deem to be the closest product. Water Pik, Inc. is not responsible for labor charges, installation, or other consequential cost. The responsibility of Water Pik, Inc. shall not exceed the original pur- chase price of the product. This warranty gives you specific legal rights. Save your receipt as proof of purchase is required for warranty action.

Register your product at www.waterpik.com

Français

Réglage du débit

Les pommes de douche Waterpik® sont équipées d’un régulateur OptiFLOW® qui limite le débit d’eau maximal à 2,5 gallons par minute à 80 lb/po_, conformément aux exigences de la loi fédérale américaine.

Dans les régions où la pression de l’eau est très faible, causant un débit d’eau médiocre dans la pomme de douche, il est possible de retirer le régulateur afin d’augmenter le débit d’eau. Pour retirer le régulateur, dévisser la grille

du filtre en la tournant dans le sens horaire. Ôter le régulateur avec une pince à bec effilé et réinstaller la grille du filtre.

joint	régulateur
	de débit

Instruction Manual

Manuel d’instructions Manual de Instrucciones

Operation

The 9” AquaScape™ Total Body Shower has two spray settings, as opposed to the one spray setting on the 6” model. To change settings from either the full-body spray or the concentrated power spray, push the spray change button on the back of the showerhead so it extends to the opposite side of its current position.

tamis de filtration

articulation sphérique écrou

Flow Control

Waterpik® showerheads are equipped with an OptiFLOW® regulator that limits maximum water flow to 2.5 gallons per minute at 80 psi as mandated by U.S. federal law.

You can change the orientation of your showerhead by loosening nut and repositioning shower head; re-tighten nut. This allows for higher, lower or wider spray coverage.

Have any questions or need assistance?

Go to www.waterpik.com and click on Showerheads and click on the Ask Ann! link.

Installation

Aucun outillage n’est nécessaire.

Enlever la vieille pomme de douche. Nettoyer parfaitement le filetage du

In areas with extremely low water pressure, causing the shower water flow to be unsatisfactory, the flow regulator may

be removed to improve the water flow in the showerhead. To remove, unscrew filter screen by turning counterclockwise. Remove regulator with needle-nose pliers and replace

Spray change button

In the U.S., call our toll-free Customer Assistance Line,

1-800-525-2774

In Canada, call our toll-free Customer Assistance Line,

1-888-226-3042

Patents pending.

Outside the U.S. write us at: Water Pik, Inc.

1730 East Prospect Road Fort Collins, CO U.S.A. 80553-0001 www.waterpik.com

tuyau. Visser à la main l’articulation sphérique sur le tuyau. Pour aligner l’unité avec le conduit de douche, desserrer l’écrou et repositionner la pomme de douche. Resserrer l’écrou.

filter screen.

If product malfunctions or becomes damaged, stop use and contact Water Pik, Inc. for replacement and/or repair.

Waterpik®, Waterpik® (stylized) and OptiFLOW® are registered trademarks of Water Pik, Inc. AquaScape™ is a trademark of Water Pik, Inc.

tuyau

WasherFlow Regulator

Filter

Screen

Pivot Ball

Nut

Care and Cleaning

•Remove showerhead from pipe. Then, remove filter screen with pliers by turning counterclockwise. Clean filter screen at least once a year, or whenever you notice a drop in water pressure. After cleaning, reinsert the filter screen and ensure that the washer is in place before reinstalling the showerhead.

•Cleaning is required when mineral deposits appear on the spray orifices to maintain proper working conditions. Clean by soaking in household vinegar.

•Do not clean or rinse any part with harsh chemicals, heavy duty cleaners, or abrasives; this may damage parts or finish and may void warranty.

©2006 Water Pik, Inc.

US Office:

1730 East Prospect Road Fort Collins, CO 80553-0001 U.S.A. www.waterpik.com

Form No. 20008990-F AC

Designed in U.S.A.

Made in China.

articulation sphérique

écrou