11
OPERATING INSTRUCTIONS

SPA-SIDE CONTROL OPERATION

Your spa-side control panel consists of an LED display and convenient touch
pads that allow you to set the water temperature and adjust the skim/filter
cycle settings, as well as control the hydrotherapy jets, and light from
spa-side.

LED DISPLAY

The LED display on your spa-side control panel continually shows the spa’s
actual water temperature. In certain situations, it will also display other
messages. See TROUBLESHOOTING section.

TEMPERATURE CONTROL

The set temperature range is from 80°F (27 °C) to 104°F (40°C) (Temperatures
of any setting may rise slightly depending on the current use and condition of
your spa, and on outside temperature).
The factory-set temperature is 102°F (39°C). Whenever power is disconnected and then reconnected to the spa, the water temperature will automatically seek
the last set temperature.
Pressing the “TEMP ▲” button displays the spa’s set temperature. To increase the set temperature, press the “TEMP ▲”button again, once for each degree of
increased temperature desired. If you hold the button down, the set temperature will increase by one degree every half second. When the set temperature has
been reached, the “READY” icon will display.
Pressing the “TEMP ▼” button displays the spa’s set temperature. To decrease the set temperature, press the “TEMP ▼” button again, once for each degree of
decreased temperature desired. If you hold the button down, the set temperature will decrease by one degree every half second. When the spa water has
reached the set temperature, the “READY” icon will display.

JET PUMP CONTROL

MYSTIQUE

®

LED LIGHTING

Your spa is equipped with the six color Mystique Led Light system. Press the “LIGHT” button on the control panel, for the highest level of brightness. Pressing the
“LIGHT” button a second and third time will dim the light to lower intensities. Press “LIGHT” button a fourth time to turn the light off.
To activate the automatic color sequence, press “SET” button. While the “SET” icon is flashing press the “LIGHT” button within 5 seconds, the “LIGHT” and “SET” icon
will stop blinking. The automatic color sequence emits six different colors - blue, aqua, green, amber, red, and magenta. Once activated, the “LIGHT” icon will blink. To
stop at a specific color, press the “SET” button. While the “SET” icon is flashing press the “LIGHT” button within 5 seconds, the “LIGHT” and “SET” icon will stop
blinking.
To restart the automatic color sequence, press the “SET” button. While the “SET” icon is flashing press the “LIGHT” button within 5 seconds, the “LIGHT” and “SET”
icon will stop blinking as the color sequence resumes.
LOCK FEATURES
The locking features, TEMPERATURE LOCK and SPA LOCK, are enabled from the control panel by a specific combination of buttons. Once enabled, a lock will remain
active until the specific button combination is applied to disable the lock. Even if power is disconnected from the spa and soon thereafter reapplied (such as a power
outage), the lock will remain in place.

SPA LOCK

To activate the Spa Lock feature, press “SET” button. When the “SET”icon flashes push “TEMP ▼” button. Do not press any other buttons on the control panel
until the “SET” icon stops flashing. The SLOCsymbol is displayed and the “SET” icon will stop flashing. To deactivate the Spa Lock, press “SET” button.
When the “SET” icon flashes press the “TEMP ▼” button. Do not press any other buttons on the control panel until the “SET” icon stops flashing. TheSLOC
symbol is no longer illuminated and the “SET” icon will stop flashing .

TEMPERATURE LOCK

To activate the Temperature Lock feature, press “SET” button. When the “SET” icon flashes push “TEMP ▲”button. Do not press any other buttons on the
control panel until the “SET” icon stops flashing. The TLOCsymbol is displayed and the “SET” icon will stop flashing. To deactivate the Temperature Lock,
press “SET” button. When the “SET” icon flashes press the “TEMP ▲”button. Do not press any other buttons on the control panel until the “SET” icon stops
flashing. The TLOC symbol is no longer illuminated and the “SET” icon will stop flashing.