Manuals / Wayne-Dalton / Household Appliance / Door

Wayne-Dalton 200-20 manual T H E R M O S Pa N, Sectional Door Systems, Distributed By

Models: 200-20

1 4
Download 4 pages 30.58 Kb
Page 4
Image 4
T H E R M O S PA N ®

SECTIONAL DOOR SYSTEMS

T H E R M O S PA N ®

2 0 0 - 2 0

Note to specifiers: Words in parentheses indicate frequently specified and highly recommended options.

PART I – GENERAL

 

1.07

A.

Delivery, Handling, Storage

 

D.

Counterbalance:

1.01

Section Includes

 

 

Deliver products in manufacturer’s original containers,

 

1. Springs shall be torsion type,low-stress,helical

A.

Sectional overhead doors [manually] [motor]

 

B.

dry,undamaged,seals and labels intact.

 

 

wound,oil-tempered spring wire to provide

1.02

operated with accessories and components.

 

Store and protect products in accordance with

 

minimum [25,000 standard] [50,000] [100,000]

Related Work

 

1.08

manufacturer’s recommendations.

 

 

cycles of use,on continuous steel [solid].

A.

Opening preparation, miscellaneous or structural steel

Warranty

 

 

2. Spring fittings and drums made of die cast,high

 

work, access panels finish or field painting are in the

 

A.

Provide manufacturer’s standard SEVENYEAR warranty

 

strength aluminum.

 

scope of work of other trades and divisions of these

 

 

against separation/degradation of the polyurethane

 

3. Pre-formed galvanized steel aircraft cable shall

1.03

specifications.

 

 

 

 

foam from the steel skin of the panel under provisions

2.03

provide a minimum of a 5:1 safety factor.

Reference Standards

 

 

 

of Section 01700. Standard manufacturer’sTENYEAR

Operation

A.

ANSI/DASMA 102 – American National

 

 

warranty against cracking,splitting or deterioration due

A. Operation shall be [manual push-up] [chain hoist]

 

Standards Institute [A216.1] Specifications for sectional

 

 

to rust-through.TENYEARS on insulation value.

 

[motor] [motor with chain hoist]. Manufacturer does

 

overhead doors published by Door & Access Systems

PARTII – PRODUCTS

 

 

not recommend chain hoists or jack shaft operators

 

Manufacturers Association, International in bulletin

 

 

on the following track applications.

B.

102-1990.

– Zinc [hot-dipped galvanized]

2.01

Manufacturer

 

 

•15" radius standard lift with roof pitch less than 2:12

ASTM A123

 

A.

Wayne-Dalton or approved equal Thermospan

 

•Hi-lift less than 24"

C.

coatings on iron and steel products.

 

 

200-20insulated sectional overhead doors of steel

 

•Hi-lift between 12" – 23" with roof pitch less than 1:12

ASTM A216

– Specifications for sectional overhead

 

 

construction complete as specified in this section and

 

•Low headroom track

D.

type doors.

– Steel wire, oil-tempered for

 

 

as manufactured by Wayne-Dalton Corp.,Mt.

 

Special chain hoist assemblies (using a trolley rail)

ASTM A229

2.02

Hope,Ohio.

 

2.04

are available for the above track systems.

E.

mechanical springs.

 

Materials

 

Locks

ASTM A-653-94– Steel sheet, zinc-coated

 

A.

Door Sections:Shall be of steel/polyurethane/steel

A. Locks shall engage the right-hand vertical track and

 

[galvanized] by the hot-dipped process,

 

 

sandwich type construction with thermal break and

 

utilize [an interior side lock] [standard size rim cylin-

F.

commercial quality.

 

 

 

calculated materials“R”- value of 17.50,in accordance

2.05

der].

ASTM D1929 – Ignition temperature test to

 

 

with industry guidelines.

 

Weatherstripping

 

determine flash and ignition temperature of

 

 

1. Exterior Skin:Structural quality,hot-dipped galvanized

A. Doors shall be equipped with top and side seals

G.

foamed plastics.

 

 

 

steel,20 gauge white flush smooth.

 

 

to seal against header, co-polymer

ASTM E84-91A–Tunnel test for flame spread

 

 

2. Interior Skin:Structural quality,hot-dipped,galvanized

 

joint seals between sections, and vinyl “bulb”

and smoke developed index.

 

 

 

steel,factory finished with a polyester primer and

 

shaped astragal provided on the bottom

H.

ASTM E330

– Structural performance of exterior

 

 

white finish coat. Interior skin shall have two 13/4"

2.06

section.

 

windows,curtain walls,and doors by uniform static air

 

 

roll-formed integral struts sealed with polypropylene

Glazing

I.

pressure difference.

 

 

 

rib caps per section.

 

A.

Optional.

ASTM E413-87– Sound transmission class.

 

 

3. Ends of section shall be sealed with 18 or 16

2.07

Windload

J.

Acoustical performance value = 23

 

 

 

[14 GA.] gauge hot-dipped galvanized steel full

A. Windload – per DASMA 102-2003 and as required by

ASTM E1332-90– Outdoor-indoor transmission

 

 

height end caps.

 

 

local codes.

K.

class. Acoustical performance value

= 22.

 

 

4. Insulation:Cavity shall be filled with foamed-in-place

PARTIII – EXECUTION

ASTM E283 –Air infiltration for

= .07CFM/FT2 at 15

 

 

CFC free polyurethane core separated by a factory

1.04

MPH.

 

 

 

 

extruded thermal break.

 

3.01

Installation

Quality Assurance

 

 

 

5. Insulated sections shall be tested by an I.C.B.O.

A.

General:

A.

Sectional overhead doors and all accessories and

 

 

certified laboratory in accordance withASTM E-84-

 

1. Install doors in accordance with

 

components required for complete and secure

 

 

91A and shall achieve a Flamespread Index of 10 or

 

manufacturer’s instructions and standards.

 

installations shall be manufactured as a system from

 

 

less,and a Smoke Developed Index of 210 or less.

 

Installation shall be by an authorized

B.

one manufacturer.

 

 

 

6. Insulation material shall be tested by an I.C.B.O.

 

Wayne-Dalton representative.

Sectional overhead doors shall be tested and labeled

 

 

certified laboratory in accordance withASTM

 

2. Verify that existing conditions are ready to receive

 

certifying compliance withASTM D1929 andASTM

 

 

D-1929 and shall achieve a minimum Flash Ignition

 

sectional overhead door work.

1.05

E84-91A standards.

 

 

 

temperature of 734 degrees F,and a minimum Self

 

3. Beginning of sectional overhead door work means

Systems Description

 

 

 

Ignition temperature of 950 degrees F.

B.

acceptance of existing conditions.

A.

Sectional Overhead Door:Type:

 

 

 

7. Insulated sections shall be tested and meet all

Install door complete with necessary hardware,jamb

B.

Thermospan 200-20

 

 

B.

requirements of the UBC 17-5 corner burn.

 

and head mold strips, anchors,inserts,

Mounting:Continuous angle mounting for [steel]

 

Track:Track design shall be [standard lift] [high lift]

 

hangers,and equipment supports in accordance with

C.

[wood] jambs

 

 

 

 

[vertical lift] [low headroom].Vertical mounting angles

 

final shop drawings,manufacturer’s

Operation:[manual push-up] [chain hoist]

 

 

shall be hot-dipped galvanized.Track size shall be [2"]

 

instructions,and as specified herein.

D.

[motor] [motor with chain hoist]

 

 

 

[3"].Vertical track shall be graduated to provide wedge

C. Fit,align and adjust sectional overhead door assemblies

Material:Galvanized steel with polyester finish paint

 

 

type weathertight closing with continuous angle mounting

 

level and plumb for smooth operation.

E.

Insulation:Polyurethane

 

 

 

for [steel] [wood] jambs,and shall be fully adjustable to

D. Upon completion of final installation,lubricate,test and

1.06

Submittals

 

 

 

 

seal door at jambs. Horizontal track shall be reinforced

 

adjust doors to operate easily,free from warp,twist or

A.

Shop Drawings:Clearly indicate the following:

 

 

with continuous angle of adequate length and gauge to

 

distortion and fitting for entire perimeter.

 

1. Design and installation details to withstand

 

 

minimize deflection.

 

 

Note:Architect may consider providing a

 

standard windload.

 

 

 

Note: Horizontal track applies to standard lift,high lift,

 

schedule when more than one sectional

 

2. All details required for complete operation

 

C.

low headroom and follow-the-roof designs only.

3.02

overhead door or opening type is required.

 

and installation.

 

 

Hardware:Hinge and RollerAssembly:

 

Materials (See note above.)

 

3. Hardware locations.

 

 

 

1. Hinges and brackets shall be made from

 

 

 

4. Type of metal and finish for door sections.

 

 

hot-dipped galvanized steel.

 

 

 

 

5. Finish for miscellaneous components

 

 

2. Track rollers shall be case-hardened inner steel

 

 

B.

and accessories.

 

 

 

races with 10-ball [2"] [3"] rollers.

 

 

 

Product Data:Indicating manufacturer’s product

 

 

3. All factory authorized attachments shall be made at

 

 

 

data,and installation instructions.

 

 

 

locations indicated and reinforced with backup plates.

 

 

Specifications and technical information also available at www.arcat.com, SpecWizard™, and Sweets.com®.

Distributed By:

www.wayne-dalton.com/commercial

Item #332537 Revised 9/2007

For technic l i formation, visit:

Printed in U.S.A.

 

© 2007 Wayne-Dalton Corp. • One Door Drive • Mt. Hope, Ohio 44660 • 800-764-1457

 

Mt. Hope, OH • Dalton, OH • Trail, OH • Pensacola, FL • Portland, OR

 

Page 3
Page 4
Image 4
Wayne-Dalton 200-20 manual T H E R M O S Pa N, Sectional Door Systems, Distributed By
Page 3