Wayne-Dalton ALUMINUM FULL-VIEW451, Sectional Door Systems, For technic l i formation, visit

SECTIONAL DOOR SYSTEMS

ALUMINUM FULL-VIEW 451 & 452
Note to specifiers: Words in parentheses indicate frequently specified and highly recommended options.
PART I – GENERAL			PART I I – PRODUCTS		2.05	Weatherstripping
1.01	Section Includes		2.01	Manufacturer	A.	Doors shall be equipped with vinyl joint seals between
A.	Sectional overhead doors [manually] [motor] operated		A.	Wayne-Dalton or approved equal AFV 451/452		sections and vinyl“bulb” shaped astragal provided on
	with accessories and components.			overhead doors of aluminum alloy 6063-T6		the bottom section.Optional top seal and jamb
1.02	Related Work			construction complete as specified in this section and		seal are available.
				as manufactured by Wayne-Dalton Corp.	2.06	Glazing
A.	Opening preparation, miscellaneous or structural steel		2.02	Materials
	work, access panels finish or field painting are in the				A.	Optional.
	scope of work of other trades and divisions of these		A.	Door Sections: Shall be of aluminum alloy 6063-T6,	2.07	Windload
	specifications.			1 3/8" thick stiles and rails, joined with self tapping
1.03	Reference Standards			screws	A. Windload – per DASMA 102-2003 and as required by
				1. Rails –Top and bottom rails with 3 1/2" wide, lower		local codes.
A.	ANSI/DASMA 102 – American National			intermediate rail 1 3/8", upper rail 1 5/8" , minimum	PART III – EXECUTION
	Standards Institute [A216.1] Specifications for sectional			wall thickness 0.062”.
	overhead doors published by Door & Access Systems			2. Stiles –Top, bottom, and end stiles are 3 1/2" wide,	3.01	Installation
	Manufacturers Association International in bulletin			center stile 3” wide, minimum wall thickness	A.	General:
B.	102-1990.	– Zinc [hot-dipped galvanized]		0.062”.		1. Install doors in accordance with manufacturer’s
	ASTM A123			3. Glazing – 1/8" DSB (451) or 1/2" double insulated		instructions and standards.Installation shall be by an
C.	coatings on iron and steel products.		B.	SSB (452)		authorizedWayne-Dalton representative.
	ASTM A216	– Specifications for sectional overhead		Track:Track design shall be [standard lift] [high lift]		2. Verify that existing conditions are ready to receive
D.	type doors.	– Steel wire, oil-tempered for		[vertical lift] [low headroom].Vertical mounting angles		sectional overhead door work.
	ASTM A229			shall be hot-dipped galvanized.Track size shall be [2"]		3. Beginning of sectional overhead door work means
E.	mechanical springs.			[3"].Vertical track shall be graduated to provide wedge	B.	acceptance of existing conditions.
	ASTM E330	– Structural performance of exterior		type weathertight closing with continuous angle		Install door complete with necessary hardware,jamb
	windows, curtain walls, and doors by uniform static air			mounting for [steel] [wood] jambs,and shall be fully		and head mold strips,anchors,inserts,hangers,and
	pressure difference.			adjustable to seal door at jambs [bracket mounting for		equipment supports in accordance with final shop
1.04	Quality Assurance			wood jambs]. Horizontal track shall be reinforced with		drawings,manufacturer’s instructions,and as specified
				continuous angle of adequate length and gauge to	C.	herein.
A. Sectional overhead doors and all accessories and				minimize deflection.		Fit,align and adjust sectional overhead door assemblies
	components required for complete and secure		Note:	Horizontal track applies to standard lift,high lift,low	D.	level and plumb for smooth operation.
	installations shall be manufactured as a system from					Upon completion of final installation,lubricate,test and
	one manufacturer.		C.	headroom and follow-the-roof designs only.		adjust doors to operate easily,free from warp,twist or
1.05	Systems Description			Hardware:Hinge and RollerAssembly:		distortion and fitting for entire perimeter.
				1. Hinges and brackets shall be made from hot-	Note: Architect may consider providing a schedule when
A.	Sectional Overhead Door:Type:			dipped,galvanized steel.
B.	AFV 451/452			2. Track rollers shall be case-hardened inner		more than one sectional overhead door or opening
	Mounting: Continuous angle mounting for [steel]			steel races with 10-ball [2"] [3"] rollers.		type is required.
C.	[wood] jambs [bracket mounting for wood jambs]			3. All factory authorized attachments shall be	3.02	Materials (See note above.)
	Operation: [manual push-up] [chain hoist] [motor]		D.	made at locations indicated.
D.	[motor with chain hoist]			Counterbalance:
	Material:Aluminum Alloy 6063T6 [clear anodized]			1. Springs shall be torsion type,low-stress,helical
	[acrylic enamel]			wound,oil-tempered spring wire to provide
1.06	Submittals			minimum [10,000 standard] [25,000] [50,000]
				[100,000] cycles of use,on continuous steel [solid].
A.	Shop Drawings: Clearly indicate the following:			2. Spring fittings and drums made of die cast,high
	1. Design and installation details to withstand			strength aluminum.
	standard windload.			3. Pre-formed galvanized steel aircraft cable shall
	2. All details required for complete operation			provide a minimum of a 5:1 safety factor.
	and installation.		2.03	Operation
	3. Hardware locations.
	4. Type of metal and finish for door sections.		A.	Operation shall be [manual push-up] [chain hoist]
	5. Finish for miscellaneous components and			[motor] [motor with chain hoist].
B.	accessories.		Note:	Manufacturer does not recommend chain hoists or
	Product Data: Indicating manufacturer’s product
	data, and installation instructions.			jack shaft operators on the following track applications.
1.07	Delivery, Handling, Storage			• 15" radius standard lift with roof pitch
				less than 2:12
A.	Deliver products in manufacturer’s original containers,			• Hi-lift less than 24"
B.	dry, undamaged, seals and labels intact.			• Hi-lift between 12" – 23" with roof pitch
	Store and protect products in accordance with			less than 1:12
	manufacturer’s recommendations.			• Low headroom track
1.08	Warranty			Special chain hoist assemblies (using a trolley rail)
				are available for the above track systems.
A.	Provide manufacturer’s standard ONEYEAR warranty		2.04	Locks
	against defects in workmanship and material.
			A.	Locks shall engage the right-hand vertical track
				and utilize [an interior side lock] [standard size
				rim cylinder].

Specifications and technical information also available at www.arcat.com, SpecWizard™, and Sweets.com®.

Distributed By:

www.wayne-dalton.com/commercial	Item #332549 Revised 9/2007
For technic l i formation, visit:	Printed in U.S.A.
© 2007 Wayne-Dalton Corp. • One Door Drive • Mt. Hope, Ohio 44660 • 800-764-1457
Mt. Hope, OH • Dalton, OH • Trail, OH • Pensacola, FL • Portland, OR