SERVICE AND ADJUSTMENTS

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

ADJUSTMENT

BOLT

02239

FIG. 22

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 23)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

• Block up axle securely.

• Remove axle cover, retaining ring and washers to allow

wheel removal (rear wheel contains a square key - Do

not lose).

• Repair tire and reassemble.

• On rear wheels only: align grooves in rear wheel hub

and axle. Insert square key.

• Replace washers and snap retaining ring securely in

axle groove.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

• Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 23

FIG. 24

REPLACING BATTERY (See Figs. 25 and 26)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal brace- lets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

22

Page 22
Image 22
Weed Eater 186913 manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

186913 specifications

The Weed Eater 186913 is a remarkable addition to the world of outdoor power equipment, specifically designed to tackle the challenges of yard maintenance with precision and ease. This versatile and powerful string trimmer stands out for its user-friendly features and advanced technologies.

At the heart of the Weed Eater 186913 is its robust 25cc two-cycle engine, delivering a strong performance that ensures your lawn looks pristine. This high-performance engine provides an impressive power-to-weight ratio, making it easy to maneuver around your yard while maintaining impressive cutting capability. With a quick-start feature, users can expect minimal effort when firing up the trimmer, allowing for more time spent trimming and less time struggling with start-ups.

One of the key characteristics of the Weed Eater 186913 is its lightweight design. Weighing in at just 10 pounds, it reduces fatigue during extended use, making it an ideal choice for both homeowners and professionals. Additionally, the trimmer is equipped with an adjustable handle that can be tailored to suit the user's height and comfort, further enhancing the overall experience.

The Weed Eater 186913 employs a dual-line cutting system that allows for efficient trimming of grass and weeds. The automatic feed spool releases line as needed, minimizing interruptions and maximizing productivity. This technology ensures that the user can maintain a consistent cutting length without the hassle of manual line adjustments, making it a time-saver in outdoor maintenance.

Durability is another hallmark of the Weed Eater 186913. The trimmer is constructed with high-quality materials, ensuring longevity and reliability even under rigorous conditions. This makes it an excellent investment for those who require a dependable tool to tackle their landscaping needs.

For enhanced control and precision, the Weed Eater 186913 features a curved shaft design, allowing for easy navigation around flower beds and tight corners. This ergonomic design helps users achieve professional-looking results without the discomfort commonly associated with traditional straight-shaft models.

In conclusion, the Weed Eater 186913 combines power, convenience, and durability into one efficient package, making it an excellent choice for anyone in need of a reliable string trimmer. With its advanced engine technology, user-friendly features, and thoughtful design, it stands ready to help you maintain a beautiful and well-manicured lawn. Whether tackling overgrown weeds or edging along sidewalks, the Weed Eater 186913 is equipped to handle the job with ease.