S Push and release the engine ON/STOP switch.

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2 in. (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle.

The most efficient line length is the maximum length allowed by the line limiter.Always keep the shield in place when the tool is being oper- ated.

To advance line:

SOperate the engine at full throttle.

SHold the trimmer head parallel to and above

the grassy area.

STap the bottom of the trimmer head lightly on the ground one time. Approximately 2 in. (5 cm) of line will be advanced with each

tap.

Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or asphalt can cause excessive wear to the trimmer head.

If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to ob- tain the most efficient line length.

WARNING: Use only 0.080! (2 mm) diameter line. Other sizes of line will not ad- vance properly and can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

SThe tip of the line does the cutting. You will achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences.

SFor trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

SDuring light duty cutting.

S Near objects around which the line can wrap such as small posts, trees or fence wire.

SFor mowing or sweeping, use full throttle for a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

SCALPING -- The scalping technique re- moves unwanted vegetation. Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear.

MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

6

Page 5 Page 7
Page 6
Image 6
Weed Eater 530086928 instruction manual Trimmer Line Advance, Cutting Methods, Push and release the engine ON/STOP switch
Page 5 Page 7

530086928 specifications

The Weed Eater 530086928 is an exceptional tool that stands out in the world of lawn care equipment. Designed for both casual gardeners and professional landscapers, this gas-powered string trimmer combines power with versatility, making it a reliable choice for various outdoor tasks.

One of the main features of the Weed Eater 530086928 is its robust 25cc engine, which delivers ample power to efficiently tackle tough weeds and overgrown grass. The lightweight design, at just under 10 pounds, allows for easy maneuverability, reducing user fatigue during extended use. This makes it ideal for users looking to maintain their lawns without the strain that heavier models may impose.

Another key characteristic of the Weed Eater 530086928 is its adjustable cutting head. This feature allows users to easily switch between different angles for optimal trimming, ensuring that hard-to-reach areas are effectively addressed. Additionally, the cutting width of up to 17 inches enables faster trimming, allowing users to cover more ground in less time.

The dual-line system that the Weed Eater 530086928 employs is another standout technology. This system ensures that the trimmer utilizes two lines of nylon string, creating a cleaner and more efficient cut. The bump feed mechanism simplifies line advancement, allowing users to easily extend the cutting line without stopping the engine — a feature particularly appreciated during extensive gardening projects.

Durability is also at the forefront of the Weed Eater 530086928's design. The trimmer features high-quality materials and components designed to withstand the rigors of regular use. Coupled with a user-friendly starting system, this machine is manageable for individuals of varying experience levels.

Furthermore, the ergonomic handle design provides comfortable grip and control, enabling users to navigate complex lawns while maintaining accuracy. The inclusion of anti-vibration technology contributes to the overall user experience, diminishing the harsh impacts of vibration on the hands and arms.

In summary, the Weed Eater 530086928 delivers a powerful, efficient, and user-friendly experience for all lawn care enthusiasts. With a combination of a powerful engine, adjustable cutting head, dual-line system, and ergonomic design, it has cemented its place as a dependable choice for tackling any trimming task with ease and precision.
Top Page Image Contents