This engine is certified to operate on unleaded gasoline. Gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand oil is recommended. (A 40:1 ratio is ob- tained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline). When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules under FUEL

SAFETY.

HOW TO STOP YOUR UNIT

To stop the engine, push and release the en- gine STOP switch. The switch will automati- cally return to the ON position. Wait 5 sec- onds before attempting to restart unit to allow switch to reset.

HOW TO START YOUR UNIT

Starting Position

Choke lever

Trigger

Primer Bulb Muffler

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

COLD ENGINE STARTING (or a warm engine after running out of fuel)

SSet unit on a flat surface.

SSlowly press the primer bulb 6 times.

SMove choke lever to FULL CHOKE posi- tion.

S Squeeze the throttle trigger fully and hold through all remaining steps.

SPull starter rope handle sharply 6 times. S Move choke lever to HALF CHOKE posi-

tion.

S Pull starter rope handle no more than 6 pulls, until engine runs.

S Allow engine to run 10 seconds, then move choke lever to OFF CHOKE position.

STARTING A WARM ENGINE

SMove choke lever to OFF CHOKE position. S Pull starter rope handle until engine runs.

S If engine does not start in 5 pulls, follow instructions in STARTING A COLD EN- GINE.

OPERATING POSITION

ALWAYS WEAR:

 

 

 

 

Eye Protection

 

 

 

 

Long Pants

Heavy Shoes

Cut from your right to your left.

ADVANCING THE CUTTING LINE

Advance line by tapping the bottom of the cut- ting head lightly on the ground while engine is running at full speed. The metal blade (Line Limiter) attached to the shield will cut the line to the proper length.

REPLACING THE LINE

SRemove spool by firmly pulling on tap but-

ton.

SClean entire surface of hub and spool.

S Replace with a pre-wound spool, or cut a length of 20 feet of .080” (2 mm) diameter Weed Eaterr brand line. Never use wire, rope, string, etc., which can break off and become a dangerous missile.

SInsert one end of the line about 1/2 inch (1 cm) into the small hole on the inside of spool.

Small

 

 

 

 

 

 

 

 

Hole

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spool

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line in Notch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hub

Line exit hole

 

S Wind the line evenly and tightly onto the spool. Wind in the direction of the arrow found on the spool.

SPush the line into the notch, leaving 3 to 5

inches (7 -- 12 cm) unwound.

SInsert the line into the the exit hole in the hub

as shown in the illustration.

SAlign the notch with the line exit hole.

SPush spool into hub until it snaps into place.

4

Page 4
Image 4
Weed Eater 530088830 HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Warm Engine, Operating Position