STARTING POSITION

Blower

Vacuum

WARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing serious injury to by- standers or the operator.

STARTING A COLD ENGINE

1.Move throttle lever to the position.

2.Move choke lever to the FULL CHOKE position.

3.Slowly press the primer button 8 times.

Throttle Lever

 

Primer Button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choke Lever

4.Pull starter rope sharply until engine at- tempts to run, but no more than5 pulls (be- low 30_ F, 8 pulls).

NOTE: If engine attempts to start before the 5th pull, go to next step immediately.

5.Move the choke lever to the HALF CHOKE position.

6.Pull the starter rope sharply until the en- gine runs, but no more than 5 pulls (below 30_ F, 10 pulls).

7.After a 5 second warm--up, move the choke lever to the RUN position.

8.Allow the unit to run for 30 more seconds at the RUN position before moving the

throttle lever to position.

If engine has not started after 5 pulls (at HALF CHOKE), repeat STARTING A COLD ENGINE procedure. If engine still does not start, proceed to STARTING A FLOODED ENGINE.

9.To stop the engine, move the throttle lever to the STOP position.

STARTING A WARM ENGINE

NOTE: If fuel tank is empty, add fuel; then, follow STARTING A COLD ENGINE proce- dure. Do not fill fuel tank while engine is hot.

1.Move throttle lever to the position.

2.Pull starter rope sharply until engine runs, but no more than 5 pulls.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

3.To stop the engine, move the throttle lever to the STOP position.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position. Move throttle

lever to the fast position

; then, pull rope

until engine starts. After engine starts, move the

throttle lever to the slow position to allow engine to idle.

Starting could require pulling the starter rope many times depending on how badly the unit is flooded.

If unit still doesn’t start refer to the TROUBLE- SHOOTING TABLE or call 1-800-554-6723.

WARNING: Avoid touching muffler unless engine and muffler are cold. A hot muffler can cause serious burns.

WARNING: Stop engine and be sure the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac- cessing movable parts.

GENERAL RECOMMENDATIONS

Thewarranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as

instructed in this manual. Various adjust- ments will need to be made periodically to properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

SSpark Plug Boot S Air Filter

S Housing Screws S Muffler

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

SFuel Tank -- Do not use unit if fuel tank shows

signs of damage or leaks.

SVacuum Bag -- Do not use vacuum bag if it is torn or damaged.

-- 7 --

Page 6 Page 8
Page 7
Image 7
Weed Eater 530163804 Starting a Cold Engine, Starting a Warm Engine, Starting a Flooded Engine, General Recommendations
Page 6 Page 8

530163804 specifications

The Weed Eater 530163804 is a versatile and efficient tool designed for both the casual gardener and the dedicated landscaping professional. Renowned for its reliability and performance, this weed eater has earned a place in the arsenal of those who prioritize lawn care.

One of the standout features of the Weed Eater 530163804 is its lightweight design, making it easy to maneuver around various terrains. Weighing in at just a few pounds, this tool minimizes fatigue during extended use, allowing users to tackle larger areas without feeling overworked.

Powered by a robust 2-cycle engine, the Weed Eater 530163804 delivers ample power for cutting through dense weeds and grass. The engine's efficient design not only provides high performance but also ensures that fuel consumption remains economical. This combination of power and efficiency makes it a reliable choice for both home use and professional landscaping needs.

The weed eater features an automatic line feed system, which simplifies the process of reloading the cutting line. This technology automatically advances the line as needed, eliminating interruptions during trimming sessions. Users can focus on their tasks without the hassle of manually adjusting the string, saving both time and effort.

Another key characteristic is the adjustable handle, which allows for a customizable grip to suit the user's comfort and working style. This ergonomic feature is particularly beneficial for individuals who spend extensive time using the tool, as it helps reduce strain on the hands and wrists.

Additionally, the Weed Eater 530163804 comes equipped with a durable cutting head designed to withstand rigorous use. Its ability to accept various trimmer lines ensures versatility in handling different types of vegetation, making it ideal for tackling a range of tasks, from light trimming to heavy-duty clearing.

Overall, the Weed Eater 530163804 stands out for its combination of power, lightweight design, and user-friendly features. Ideal for gardeners and landscapers alike, it represents a practical investment for anyone looking to maintain a clean and attractive outdoor space. With its advanced technologies and features, it continues to be a popular choice among outdoor enthusiasts.
Top Page Image Contents