SERVICE AND ADJUSTMENTS

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

 

 

FIG. 24

TERMINAL

KEPS NUT

COVER

 

HEX

 

 

 

 

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 25

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

FIG. 23

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

 

HEADLIGHT

HOOD

WIRE

CONNECTOR

 

22

FIG. 26

Page 22
Image 22
Weed Eater WET2242STC manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

WET2242STC specifications

The Weed Eater WET2242STC is a versatile and robust string trimmer designed for efficient lawn care and garden maintenance. Equipped with a powerful 22cc 2-stroke engine, this trimmer offers impressive performance that allows users to tackle tough vegetation and overgrown areas with ease. Its lightweight design, weighing just around 10 pounds, ensures comfortable handling and reduced fatigue during extended use.

One of the standout features of the WET2242STC is its innovative StartEasy technology, which simplifies starting the engine. Users can enjoy a hassle-free start with less effort, making it accessible even for those who are less experienced with power tools. This feature enhances the overall user experience by minimizing frustration and downtime that can occur with traditional pull-start engines.

The WET2242STC is equipped with a dual line automatic feed head, allowing for quick and easy line replacement without the need for tools. This system feeds out the cutting line as needed, ensuring optimal cutting performance and eliminating the hassle of manual line adjustments. The trimmer’s 17-inch cutting diameter provides an extensive area coverage, making it an ideal choice for efficiently trimming larger lawns and garden spaces.

Designed for user comfort, the trimmer features an adjustable handle that can be customized for different users and operating positions. The straight shaft design also allows for access to tight spaces and hard-to-reach areas, such as under bushes or around garden beds, delivering precision cutting where it’s needed most.

Furthermore, the WET2242STC boasts a durable construction with a solid combination of plastic and metal components, ensuring longevity and reliability for repeated use over the seasons. The lightweight frame, combined with the ergonomic design, enhances maneuverability, allowing users to navigate around obstacles seamlessly.

In summary, the Weed Eater WET2242STC stands out with its powerful engine, user-friendly features, and comfortable design. With advanced technologies like StartEasy and an automatic line feeding system, this trimmer is a fantastic solution for homeowners and gardening enthusiasts looking to maintain their outdoor spaces efficiently and effectively. Whether tackling tough weeds or outlining garden beds, the WET2242STC proves itself as a reliable partner in lawn care.