L107.6
:m)
w |
Explosion Hazard
Keep flammable materials and vapors away from dryer.
Place dryer at least 18 inches above the floor for a garage installation.
Failure to do so can result in death, explosion, fire, or burns.
For proper drying performanct
The location must provide:
Protection from weather and water: Do not store or use dryer where it will be exposed to water and weather.
L/Room temperature above 45°F (7.2”C): If room
temperature is below 45°F (7.2” C), automatic
Icvcles mav not shut off.
Id’ Level floor:’ Maximum slope under entire dryer should not be more than i inch (2.5 cm). (Ii slope is greater than 1’ (2.5 cm), install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level.
/Sturdy floor to support dryer weight of 150 pounds (68 kg).
’(/Exhaust to outdoors: To prevent large amounts of
lint and moisture from accumulating and to maintain drying efficiency, exhaust dryer to outdoors.
1 | “=x I |
dryer exhaust | vent y |
1
*from floor
with dryer feet
extended 1 \v inch (2.5 cm)
It is your responsibility to:
L/observe | all | governing | codes | and | ordinances. |
| (/consider | spacing | requirements |
| for companion | |||||
C/check | code | requirements: | Some codes limit | or | appliances. |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| |||||||||
do not | permit | installation | of | clothes | dryers | in |
| L/properly | install | dryer. |
|
|
| |||
garages, | closets, | mobile | homes or | sleeping |
|
| C/m&e | sure | you | have |
| na~nccxrw | fnr | |||
quarters. | Contact | your | local | building | inspector. |
| proper | installation. |
|
|
|
| ||||
1 |
|
|
|
|
|
|
|
|
|
|
|
| ||||
with | the | installation | specifications | and |
|
|
|
|
|
|
|
|
| |||
Ycomply |
| (/contact | a | qualified | installer | to | insure that the | |||||||||
dimensions. |
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
| electrical | installation | meets | all | national | and local | ||||
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| codes | and | ordinances. |
|
|
|
Recessedarea/closet installation
Closet/confined area installation
If a closet door is installed: The
minimum unobstructed air openings are required. Louvered doors with equivalent air openings are acceptable.
Recessed area installation
The dryer should be exhausted to the outside for best performance.
If dryer is not exhausted outside, you must install Exhaust Deflector Kit. Part No. 3391278. available from your dealer.
klre Hazard
Exhaust dryer outside if installed in a closet. Use Exhaust Deflector Kit #3391278 if installed in a recessed area.
Failure to follow this instruction could result in a fire.
NOTE: No
l If codes permit, dryer may be installed in a | (1 |
recessed area or closet using dimensions shown.
*Dimensions are in inches and are the minimum allowable.
l Additional spacing should be considered for ease of installation and servicing. Companion appliance spacing should also be considered,
front view | side view |
L
3’ (7.6 cm)
3’ (7.6 cm)
Lu
,:;.,il F=-
**Minimum top and bottom air openings for closet door.
***External exhaust elbow requires additional space.
front view
l *** Wall .door and floor molding may require addItIonal spacing.
Door clearance
Location must be large enough to fully open dryer door.
Electrlcal Shock Hazard
Electrical ground (earth) is required on this dryer.
Do Not ground (earth)to a gas pipe.
Do Not change the power supply cord plug. lf it does not fit the outlet, have a proper outlet installed by a qualified electrician.
Do Not have a fuse in the neutral or grounding circuit.
Do Not use an extension cord with this J dryer.
Do Not reuse old power supply cord.
Check with a qualified electrician to be sure dryer is properly grounded (earthed).
Do Not connect plug end of power supply cord into a live receptacle before connecting power supply cord to dryer terminal block.
Failure to follow these instructions could result in death or serious injury.
Important: Observe all governing codes and ordinances.
A
THE DRYER MUST BE CONNECTED WITH COPPER WIRE ONLY.
The dryer may be connected directly to the fused disconnect or circuit breaker box through
If codes permit and a separate grounding (earthing)
electrician determine that the grounding (earthing)
flexible, armored or
and connections must conform with the rating of the appliance (30 amperes).
wire is used, it is recommended that a qualified path is adequate.
Grounding (earthing) instructions
This appliance must be connected to a grounded (earthed) metal, permanent wiring
system; or an
grounding (earthing) terminal or lead on the appliance.
-