CancelingaCycle
Anytime during a cycle, press CANCEL/DRAIN. Your dishwasher starts a
NOTE: If your dishwasher does not need draining, the dishwasher stops and clears all indicators.
To stop the drain
You can press CANCEL/DRAIN again to stop the drain immediately. Be sure to drain the dishwasher before starting a new cycle.
To clear the indicators
Press CANCEL/DRAIN before starting the dishwasher to clear all options and cycles.
Changing aCycleorSetting
During the first fill of a cycle
1.Press a new cycle and/or options.
2.Check the detergent dispensers. They must be filled properly for the new cycle.
3.Press START/RESUME.
After the first fill of a cycle
1.Press CANCEL/DRAIN. Your dishwasher starts a
NOTE: If your dishwasher does not need draining, the dishwasher stops and clears all indicators.
2.Check the detergent dispensers. They must be filled properly for the new cycle.
3.Press a new cycle and/or options.
4.Press START/RESUME. (The door must be closed.)
AddingItemsDuringaCycle
You can add an item anytime before the main wash starts. Open the door and check the detergent dispenser. If the cover is still closed, you can add items.
To add items
1.Lift up the door latch to stop the cycle. Wait for the spraying action to stop before opening the door.
2.Open the door. If the detergent dispenser cover is still closed, add the item.
3.Close the door firmly until it latches.
4.Press START/RESUME. The dishwasher resumes the cycle after a
Option Selections
You can customize your cycles by pressing an option. If you change your mind, press the option again to turn off the option, or select a different option if desired.
You can change an option anytime before the selected option begins. For example, you can turn off the drying option anytime before drying begins.
After a wash cycle, the dishwasher remembers the options used. It uses the same options in the next wash cycle, if you press only
START/RESUME.
Soak & Scour (on some models)
Select this option to presoak your dishes for 4 hours in your dishwasher instead of presoaking them in the sink. When you select Soak & Scour, the dishwasher fills and then sprays for
8 minutes. It will then pause for 16 minutes while dishes soak, and then spray for 90 seconds to keep dishes wet. Pausing for 16 minutes and spraying for 90 seconds are repeated for 4 hours. At the end of the 4 hours, the dishwasher drains and then starts the cycle you have selected. The Main Wash heating time will be extended to allow the water temperature to reach 145°F (63°C). This presoaking uses only one additional fill of water and does not require special detergent. Use standard detergent according to cycle recommendations.
Hi-Temp Wash
Select this option to increase the target water temperature during the wash portions of the cycle.
This option adds heat, wash time and water to the cycle.
NOTE:
Sani Rinse
Select this option to raise the water temperature in the final rinse to approximately 155°F (68°C). The Sani Rinse option adds heat and time to the cycle. The Main Wash heating time will be extended to reach 145°F (63°C). In the Pots & Pans and Normal cycles, this
NOTE: Use the Sani Rinse option with Pots & Pans and Normal cycles. Only these sanitization cycles have been designed to meet the NSF/ANSI requirements.
Heated Dry
Select this option to dry dishes with heat.
Switching off Heated Dry skips the dry period. This is useful when loads contain plastic dinnerware that may be sensitive to high temperatures. The dishes take longer to dry and some spotting may occur. Some items (such as plastics) may need towel drying.
For best drying, use a liquid rinse aid.
NOTE: Heated Dry is an option with all cycles, except GLASS XPRESS™ and Rinse Only cycles. Heated Dry begins automatically with all cycles unless you switch it off.
14
