Whirlpool W10142914, DU1300XTV dimensions Undercounter Dishwasher, 7/8”, Product Model Numbers

®

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

PRODUCT DIMENSIONS

DU1300XTV

Electrical Requirements: 120 volt, 60 Hz, AC only, 15- or 20-amp. fuesd electrical supply. Copper wire only. Wiring must be 2-wire with ground. A time-delay fuse or circuit breaker and separate circuit is recommended.

If direct wiring dishwasher: Use flexible, armored or non-

metallic, sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.

Use a U.L.-listed or CSA-approved conduit connector.

If connecting dishwasher with a power supply cord: Use

Power Supply Cord Kit (Part No. 4317824) marked for use with dishwashers. Follow the kit instructions for installing the power supply cord.

Power supply cord must plug into a grounded three-prong, outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.

Water Supply Requirements: A hot water line with 20-

25		cm)	23-
			67/8”
	-1/4”		(60.	cm)
(64
.1
24	-1/2”
		cm)
(62	.2

33-
(86		7/8”
	cm)		min.
with
removwheels
			ed

	3/4”
(1	.9	cm)*

*Insulation may be compressed.

(not used on all models)

120 psi (138-862 kPa) water pressure. Water temperature must be 120°F (49°C) water at dishwasher. Use 3/8" O.D. copper tubing with compression fitting or flexible braided water supply line (1/2" minimum plastic tubing is not recommended). Use a 90° elbow with 3/8" N.P.T. external pipe threads on one end. Do not solder within 6" (15.2 cm) from water inlet valve.

Drain Requirements: A new drain hose is supplied with your dishwasher. If this is not long enough, use a new drain hose with a maximum length of 12' (3.7 m) (Part No. 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher.

Make sure to connect the drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.

24” cm)

21”		)	(61
.3	cm

(53

Check that all surfaces have no protrusions that would

t di h h i t ll ti

CABINET CUTOUT DIMENSIONS

Corner locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.

NOTE: Cut holes in shaded area of cabinet walls
or floor as specified below:
water line – 1/2" (1.3 cm)
drainline – 1-1/2" (3.8 cm)					24”	(6124”
direct wire – 3/4" (1/9 cm)			)		cm)
				(61		cm)**
	21”
power supply cord –	.3	cm
	(53
1-1/2" (3/8 cm)

air gap

Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or floor.

Check that all surfaces have no protrusions that would prevent dishwasher installation.

Use 1/2" (1.27 cm) minimum I.D. drain line fittings.

If required, the air gap

34	”
	cm)

4” m)

6-

(17.3/4”

2c

m)

10

should be installed in accordance with the air gap installation instructions. When connecting the air gap a rubber hose (not provided) will be needed to connect to the waste tee or disposer unit.

	.4
(8	6
	min*

		.2		c
(10
	3”				)
(7	.6	c	m

1-
(4.
	43/4”
		c
	2-		m)
	(6.
		41/2”
			cm)

(	-
	.
	71/2”
		c
	6-
	1
(15.		/4”
	9		cm)	Clear
				Area

				2”
NOTE: Shaded area of cabinet walls show where			(5	.1	cm)
*Measured from the lowest point on the underside
utility connections may be installed.
of countertop. May be reduced to 33-7/8” (86 cm)		”
by removing*Measuredwheelsfromfromthe dishwasherlowestpoint. on the underside
	-3/4cm)
	1	.4
of countertop. May be reduced to 33-7/8” (86 cm)	(4

**Minimum, measured from narrowest point of opening. by removing wheels from dishwasher.

**Minim m meas ed f om na o est point of openin

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. W10142914
Instructions packed with product. Specifications subject to change without notice.	04-07-09