Electrical connection
WARNING
Electrical Shock Hazard
Turn power supply off before connecting wires.
Electrically ground cooktop.
Failure to follow these instructions can result in death, fire, or electrical shock.
This cooktop must be connected to a grounded, metallic permanent wiring system or a ground connector should be connected to the ground terminal or wire lead on the cooktop.
This cooktop is manufactured with a frame connected, green or bare ground wire. Connect the cooktop cable to the junction box through the U.L.- or CSA- listed conduit connector. Complete electrical connection according to local codes and ordinances.
A. Where local codes permit connecting the
cable from power supply
junction box
red wires
white wire
black wires
bare or green wire
|
| U.L.- or C.S.A.- listed |
cable from cooktop |
| conduit connector |
|
|
|
Grounded neutral – Figure 2
1.Disconnect power supply.
2.Connect the flexible, armored cable from the cooktop to the junction box using a U.L.- or
connector. Tighten screws on conduit connector.
3.Connect the green (or bare) appliance cable wire with the neutral (white) wire in the junction box using
4.Connect the two black wires together; then connect the two red wires together with
B. Where local codes Do Not permit connecting the
cable from power supply
|
|
|
|
|
|
|
| junction box | ||||
| red wires |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| white wire | |||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| connector | |||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| black wires | |||||
bare or green |
|
|
|
|
|
|
| |||||
|
|
|
|
|
| |||||||
wires |
|
|
|
|
|
|
| |||||
U.L.- or C.S.A.- listed | ||||||||||||
|
|
|
|
|
| |||||||
|
|
|
|
|
| conduit connector | ||||||
|
| cable from cooktop |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |
Ungrounded neutral – Figure 3
1.Disconnect power supply.
2.Connect the flexible, armored cable from the cooktop to the junction box using a U.L.- or
3.Connect the two black wires together; then connect the two red wires together using
4.Connect the green or bare ground wire from the appliance cable to the grounded wire in the junction box or other grounded connector using twist- on connector.
5.Put a
Now start…
With cooktop in kitchen.
WARNING
Excessive Weight Hazard
Use two or more people to move and install cooktop.
Failure to do so can result in back or other injury.
1. Remove the shipping materials and tape from the cooktop. Remove the hardware package from inside the literature bag.
attachment screws |
|
for optional front | burner box |
and back location | bottom |
attachment screw
bracket (end locations recommended)
“U” shaped spring clip or small diameter hole
Standard cooktop shown. See specific instructions for installing brackets on Lift Top models.
2. Two clamp brackets are provided to clamp the cooktop to the countertop. Install the clamp brackets on each end of the burner box bottom. Optional: If cabinet construction does not provide clearance for installing brackets at burner box ends, install the brackets on the front and back of the burner box bottom.
The brackets may be installed before (see Step 2a) or after (see Step 2b) the cooktop is placed into the cutout. Note: Step 2B is not recommended for Lift Top models.
2a. If installing before the cooktop is placed into cutout:
•Remove elements and burner bowls.
•Place the cooktop upside down on a protective surface (blanket, pad). For Lift Top models: Place the cooktop right side up on the protective surface.
5
