TO ADJUST SQUEEGEE PITCH

1.Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeegee and drive forward at least 2 feet (60cm.).

2.With the squeegee down, stop the machine. Do not allow machine to roll back.

FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn off machine and remove key.

3.Determine the differences, if any, in deflection of the squeegee blade between each end and the middle. Proper adjustment is obtained when deflection is equal all the way across the squeegee blade. The bubble level should also indicate when the squeegee is adjusted properly. When the air bubble is in the center of the vial, the deflection should be even across the squeegee blade.

4.To decrease the deflection of the squeegee blade at the ends, tigthen knob near the squeegee center. To increase the deflection at the ends of the squeegee assembly, loosen knob.

5.Check the deflection of the squeegee blades again. Repeat steps 1 through 4 until the deflection is equal across the entire rear squeegee blade.

3/8”

PROPER DEFLECTION OF SQUEEGEE BLADE

MAINTENANCE

TO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION

1.Choose a smooth, level surface. Lower the squeegee and drive forward at least 2 feet (60cm).

2.With the squeegee down, stop the machine. Do not allow machine to roll back.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Observe the amount of squeegee deflection. It should deflect 3/8 in. (9.5mm) across the entire width of the squeegee.

4.To increase the squeegee deflection, turn the 2 knobs at the squeegee ends counter-clockwise. To decrease the deflection, turn the knobs clockwise.

NOTE: The deflection should be consistent along the length of the squeegee. If the deflection varies from end to end the knobs can be adjusted independently to correct the variation.

5.Turn on the key switch. Raise, then lower squeegee assembly. Drive forward at least 2 feet (60cm).

6.Repeat steps 2 through 4 until deflection of 3/8 in. (9.5mm) is reached.

3.TO REPLACE AQUA-MIZER SQUEEGEE BLADES

These squeegee blades have two wear edges. To use the second edge:

1.Remove deck shrouds.

2.Remove brushes or pad drivers.

3.Remove each of the Aqua-Mizer squeegee systems.

4.Remove the hardware from each system that retains the blade.

5.Flip the blades and replace hardware.

6.Re-install each Aqua-Mizer system, brushes or pad drivers and shrouds.

CUTTER 36V 86039100 05/01/07

4-7

 

Page 24 Page 26
Page 25
Image 25
Windsor SCX326, 10052400 manual To Adjust Squeegee Pitch, To Adjust Amount of Rear Squeegee Deflection
Page 24 Page 26

10052400, SCX326 specifications

The Windsor SCX326 is an advanced floor cleaning machine designed specifically for commercial and industrial use. Renowned for its robust build quality and superior cleaning performance, it is an essential tool for maintaining hygiene in large spaces such as warehouses, factories, and shopping malls.

One of the standout features of the SCX326 is its powerful scrubbing system, which utilizes a dual-brush design. This system delivers a thorough clean by effectively scrubbing away dirt and grime from various floor surfaces, including tile, concrete, and terrazzo. The machine is equipped with large cylindrical brushes that can tackle stubborn stains while also being gentle on the floor, ensuring long-term safety and aesthetic appeal.

The SCX326 incorporates advanced technologies to enhance its functionality and user experience. Its intuitive control panel allows operators to easily adjust water flow, brush pressure, and cleaning speed, catering to the specific needs of different environments. Additionally, the machine is designed with a high-capacity solution tank, allowing for longer cleaning sessions without the need for frequent refills, which translates to increased productivity.

A key characteristic of the Windsor SCX326 is its eco-friendly design. It utilizes a unique water-saving technology, enabling efficient water usage while still achieving optimal cleaning results. This feature not only reduces water consumption but also minimizes the use of detergents, making it an environmentally conscious choice for businesses seeking to reduce their ecological footprint.

Safety and ease of use are paramount in the SCX326’s design. The machine is equipped with user-friendly features such as ergonomic handles, smooth maneuverability, and easy-to-access maintenance points. These elements ensure that operators can navigate tight spaces and carry out routine maintenance with minimal effort.

Furthermore, the SCX326 is built with durability in mind, utilizing high-quality materials and components that withstand the rigors of daily use. This longevity ensures a solid return on investment for businesses, as they can rely on the performance of the SCX326 for years to come.

In summary, the Windsor SCX326 is a top-tier floor cleaning solution that combines powerful scrubbing capabilities, advanced technology, and a commitment to sustainability. Its user-friendly features and durable design make it an ideal choice for facilities looking to maintain cleanliness and hygiene standards in high-traffic areas.
Top Page Image Contents