Manuals / Brands / Power Tools / Battery Charger / Xantrex Technology / Power Tools / Battery Charger

Xantrex Technology Table A-2, Electrical Specifications for the DR Inverter/Chargers, - 220 Vac/60 Hz Models

Models: DR1512 DR1512E DR1512W DR1524 DR1524E DR1524W DR1548E DR2412 DR2424 DR2424E DR3624

1 122

Download 122 pages, 3.95 Mb

Specifications

A–4 975-0012-01-02 Rev A

Table A-2Electrical Specifications for the DR Inverter/Chargers

a

- 220 Vac/60 Hz Models

Model DR1512W DR2412W

AC Input Voltage 220 Vac 220 Vac

AC Input Low Transfer Voltage 80 to 210 Vac 80 to 210 Vac

AC Input Currentb45 amps 55 amps

Continuous Power (@ 25°C) 1500 VA 2400 VA

Continuous Output (@25 °C) 6.8 amps AC 6.8 amps AC

Efficiency 94% max 94% max

AC Output Voltage (rms) 220 Vac 220 Vac

Frequency: (± 0.04% Crystal controlled) 60 Hz. 60 Hz.

Surge Capability:

1 mSec Rating 20 amps AC 20 amps AC

DC Input Current:

Search Mode 0.045 amps 0.055 amps

Full Voltage 0.700 amps 0.900 amps

DC Current at Rated Power 150 amps 80 amps

Short Circuit Current 400 amps 800 amps

DC Input Voltage (nominal)c12.6 Vdc 12.6 Vdc

DC Input Voltage Range 10.8 to 15.5 Vdc 10.8 to 15.5 Vdc

Auto Low Battery Protection enabled 11 V 11 V

Charger Rate (Adjustable) 0 to 70 amps 0 to 120 amps

Common Specifications:

Voltage Regulation (maximum) ± 5%

Voltage Regulation (Typical) ±2. 5%

Waveform modified sine wave

Load Power Factor (allowed) 0.5 to 1.0 (leading or lagging)

Adjustable Load Sensing Range 5 watts minimum to 100 watts maximum

Series Operation NO

Force Air Cooling Variable speed fan

Automatic Transfer Relay 20 amps

Number of Charging Profiles 10

Three-stage Charging Yes (float, absorption, bulk)

Contents

Main DR Inverter/Charger Page Page Page About This Manual Purpose Scope Audience Organization Conventions Used The following conventions are used in this guide. Abbreviations and Acronyms Related Information WARNING Important Safety Instructions SAVE THESE INSTRUCTIONS General Wiring Requirements Explosive gas precautions WARNING Fire Hazard: WARNING: Explosion Hazard Precautions When Working With Batteries WARNING: Explosion or Fire Hazard Page Contents Important Safety Instructions 1 2 Introduction 3 Operation 4 Troubleshooting B A Specifications Page Figures Page Tab le s Page Page Introduction Features AC Side DC Side Optional Equipment Remote Control (RC8) Stacking Interface (DRI) Conduit Box (DRCB) Model Identification and Numbering Conventions Regulatory Page Pre-installation Planning Location CAUTION: Personal Injury CAUTION: Corrosion Damage Mounting Venti lati on Tools Required Hardware / Materials Required Wiring Considerations DC Terminal Connections Grounding Considerations AC Grounding Wire Routing Electrical Panels and Circuit Breaker Requirements AC Distribution Panel (Sub-Panel) DC Disconnect Battery Considerations Basic Configurations Page Page Page Generators Inverter Mounting WARNING: Personal Injury Page DC Wiring DC Circuit Grounding General DC Grounding Requirements Page Batteries Battery Types Battery Bank Sizing Battery Configuration Battery Cable Sizing WARNING: Fi re Hazard DC Disconnect and Over-current Protection Battery Cable Connections Connecting the Battery Bank to the Inverter Page Installing a Battery Temperature Sensor AC Wirin g AC Distribution Panel (Sub-panel) Mounting and Conduit Installation Accessing the AC Terminals AC Side Cover Panels Table 2-5 WARNING: Fire Hazard Page AC Output Wiring to the AC Distribution Panel (Sub-panel) AC Input Wiring - On-Grid Applications AC Input Wiring using a Generator in an On-Grid Application Page Page Series Stacking (120 Vac/60 Hz Models only) Page Page Page Front Panel Controls and Indicators POWER ON/OFF Switch Ports BATTERY SENSE Port COM Port Remote Controls (RC8/RC4) Stacking Interface Controls Battery Type Selector See Important notes that follow. Table 3-1 Battery Type Selector Switch Settings SEARCH MODE WATTS Potentiometer Battery Charger Rate Over Discharge Protection/AC Transfer Voltage Over Discharge Protection (ODP) AC Transfer Voltage Figure 3-7 ODP Enabled/Disabled Positions Figure 3-8 Typical Setting for Most Utility Application Battery Capacity LED Indicators Inverter Mode LED - Green Over Temp / Overload LED - Red / Green (error condition) Battery High/Battery Low LED - Red/Green (error condition) Charger LED - Orange / Green Audible Indicator (internal) Circuit Breakers Start-up Charger Mode 3-Stage Charging Process Equalize Charging CAUTION: Explosion Hazard Page Page Page Troubleshooting the DR Inverter Troubleshooting the DR Inverter Problem Loads Ceiling Fans Cell Phones Computers and Sensitive Electronics Consumer Electronics Clocks Decreasing Loads Dimmer Switches Fluorescent Lights Heavy Loads Page Page Page Specifications of the DR Inverter Table A-1 - 120 Vac/60 Hz Models Table A-2 Electrical Specifications for the DR Inverter/Chargers - 220 Vac/60 Hz Models Table A-2 Electrical Specifications for the DR Inverter/Chargers Table A-3 - 220 Vac/60 Hz Models - 230 Vac/50 Hz Models Table A-3 - 230 Vac/50 Hz Models Table A-4 Environmental Specifications for the DR Inverter/Charger Page Page Introduction Battery Types Deep-cycle Flooded Lead Acid (FLA) Sealed Batteries (Gel and AGM) NiCad and NiFe Batteries Understanding Battery Capacity Ratings Battery Bank Sizing Understanding Amp-hour Requirements Calculating Amp Hours Amp Hour Example Worksheet Battery bank size worksheet Battery Configurations Wiring Batteries in Series Wiring Batteries in Parallel +-+- +- +-+- +- DC Disconnect (either a circuit breaker or a fuse with a disconnect) Wiring Batteries in Series-Parallel Page Battery Information B12 975-0012-01-02 Rev A Battery Connections for Stacked Inverters Figure B-7 Example of Battery Connections for Stacked Inverters (24Vdc shown) Battery Maintenance Battery Charging Table B-4 Table B-5 Variances in Charging Voltage based on Battery Temperature Temperature Compensation Calculation Equalization Charging CAUTION: Damage to DC Loads CAUTION: Damage to Batteries General Maintenance CAUTION: Damage to Batteries Page Page C Multi-wire Branch Circuits Multi-wire Branch Circuits Figure C-2 120 Vac 120 Vac 975-0012-01-02 Rev A C3 Multi-wire Branch Circuit Wiring and Current Flow Figure C-3 Identifying Multi-wire Branch Circuits Correcting Multi-wire Branch Circuit Wiring WARNING: Fire Hazard Multi-wire Branch Circuit Wiring C6 975-0012-01-02 Rev A Figure C-5 Using a Step-down Autotransformer in Multi-wire Branch Circuit Wiring Load Center 120 Vac 120 Vac Neutral Ground Warranty and Return Information Warra nty What does this warranty cover? How do you get service? What proof of purchase is required? Disclaimer Product Exclusions Warning: Limitations On Use Return Material Authorization Policy Return Procedure If you are returning a product from outside of the USA or Canada If you are returning a product to a Xantrex Authorized Service Center (ASC) A Xantrex return Out of Warranty Service Information About Your System Index A B C F