Yamaha 150M specifications

Remove the mixer

1 Be sure that the mixer’s power switch is turned off.

2 Use a screwdriver or coin to turn each screw on the mixer from LOCK to

OPEN until it clicks.

3 Securely hold the mixer’s handles to remove it from the speaker.

Use only the mixer's handles when removing the mixer from the speaker and when carrying the mixer

separate from the speaker.

NOTE: The mixer can also be used when installed in the speaker.

When you install the mixer into the speaker, make sure to match the indentations on the speaker cabinet to the corresponding parts on the mixer, and then turn each screw from OPEN to LOCK until it clicks.

Turning the power on/off

1 Be sure that the mixer’s power switch is turned off.

2 Connect the included power cord to the [AC IN] jack, and plug the power

cord into a power outlet.

• To avoid any loud, unexpected noise from the speakers, first turn on the power to those connected

devices that are closest to the sound source.

Example: Sound source (CD player or instrument) → STAGEPAS 150M

When turning off the power to the system, reverse the order described above.

•

Before turning on the power, set the LEVEL controls and MASTER LEVEL control to their minimum setting (zero).

3 Press the mixer’s power switch to the ON position.

The POWER indicator lights. To turn the power off, press the power switch to the OFF position.The POWER indicator turns off. Power does not turn on• Is the included power cord correctly connected to a power outlet? Power shuts down suddenly• Is the volume set at high for an extended period of time? If the mixer is used at a volume beyond the permissible level, the protection circuit automatically turns the power off. Turn on the power again only after the mixer cools, since it cannot be turned on until the internal temperature goes down. Reduce the volume with the MASTER LEVEL control so that the LIMITER indicator flashes only briefly in response to the highest transient peaks.• Is the vent on the top panel of the mixer blocked? Since inadequate ventilation can result in overheating the mixer, the protection circuit may come on automatically and the power may be turned off. Turn on the power again only after the mixer cools, since it cannot be turned on until the internal temperature goes down. No sound is heard• Are external instruments (including a microphone) or speakers correctly connected to the mixer?

• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?

• Is the SPEAKER jack connected to the included speaker (300S)?• Is the POWER indicator flashing? There may be a short in the speaker cable or the connection may be faulty. Check that the speaker cable is correctly connected to the mixer and reapply the power.• Is the CLICK switch (for headphones) set to OFF?• If sound is not still output, contact your Yamaha dealer. Sound is distorted or noise is produced

• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?

• Are the MIC/LINE switches of each channels set appropriately?• Are both XLR type and phone type jacks on channels 1–2 being used (connected) at the same time? Please connect to only one of these jacks on each channel.• Is the input signal from the connected device set to an appropriate level? Reverb is not applied to the sound• Are the REVERB switches of each channels set to ON ( )?• Is the REVERB control set to an appropriate level? Getting a more powerful sound from the speakers• Is the SPEECH/MUSIC switch set to MUSIC ( )?• Are the Equalizer controls (HIGH/LOW) set to appropriate levels? Getting a clearer sound for announcements• Is the SPEECH/MUSIC switch set to SPEECH ( )?• Are the Equalizer controls (HIGH/LOW) set to appropriate levels? Outputting the signal to a main mixer• Connect a main mixer to the ST SUB OUT jack. The ST SUB OUT jack outputs the signal prior to routing through the MASTER LEVEL control. Adjust the level of output signal from the ST SUB OUT jack with the ST SUB OUT control. The ST SUB OUT control does not affect the MASTER LEVEL control. If only the L (left) ST SUB OUT jack is used, the mixer mixes the left and right signals and sends them to the jack.DimentionsSpecifications

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

712MW-01A0 Printed in China

IntroductionThank you for your purchase of the Yamaha PORTABLE PA SYSTEM STAGEPAS 150M. The STAGEPAS 150M is a versatile, compact PA system consisting of a speaker and a mixer. In order to get the most out of your new STAGEPAS 150M and its sophisticated functions, we suggest you read through this manual thoroughly. Also keep it in a safe place for future reference.Features● Two-way, 8-inch (20 cm) speaker system The built-in speaker delivers high-quality powerful sound from an exceptionally compact cabinet. The scratch-resistant speaker is rugged enough for outdoor use.● Powered mixer The powered mixer is a convenient, high-performance all-in-one unit that includes EQ and reverb. With two monaural inputs and three stereo inputs, the STAGEPAS 150M can be connected to a wide range of instruments and devices.● Convenient storage The STAGEPAS 150M can be used in even the most cramped quarters, inside or outside, since the mixer is built into the speaker cabinet.Package ContentsSpeaker (300S), mixer, power cord, speaker cable, Owner’s Manual (this booklet)

NOTE: The mixer is installed in the speaker when the STAGEPAS 150M leaves the factory.

Owner’s Manual

OPEN

LOCK

OPEN

LOCK

OPEN

LOCK

OPEN

LOCK

OPEN

Troubleshooting

Before turning on the mixer

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as

indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product

use only high quality shielded cables. Cable/s supplied with this product MUST be

used. Follow all installation instructions. Failure to follow instructions could void your

FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed

in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these

requirements provides a reasonable level of assurance that your use of this product in

a residential environment will not result in harmful interference with other electronic

devices. This equipment generates/uses radio frequencies and, if not installed and

used according to the instructions found in the users manual, may cause interference

harmful to the operation of other electronic devices. Compliance with FCC regulations

does not guarantee that interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined by turning the unit

"OFF" and "ON", please try to eliminate the problem by using one of the following

measures:Relocate either this product or the device that is being affected by the

interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or

install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna

lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the

local retailer authorized to distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Corporation of America, Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha

Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/

Yamaha Manual Library: http://www.yamaha.co.jp/manual/

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The above warning is located on the bottom

of the mixer and the rear of the speaker.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the

presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the product.

Explanation of Graphical Symbols

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table specified

by the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused

for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Water warning

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings. If any liquid such as water seeps into the device, turn

off the power immediately and unplug the power cord from the AC outlet.

Then have the device inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

If you notice any abnormality

• If the power cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the device, or if any unusual smells

or smoke should appear to be caused by it, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualified Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

Power supply/Power cord

• Remove the electric plug from the outlet when the device is not to be used

for extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

Location

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn

off the power switch and disconnect the plug from the outlet. Even when

the power switch is turned off, electricity is still flowing to the product at

the minimum level. When you are not using the product for a long time,

make sure to unplug the power cord from the wall AC outlet.

• Do not use the device in a confined, poorly-ventilated location. Make sure

that there is adequate space between the mixer and surrounding walls or

other devices: at least 30 cm at the sides, 30 cm behind and 30 cm

above. If the mixer is to be used installed into the speaker cabinet, make

sure to allow adequate space between the speaker and the surrounding

walls or other devices: at least 30 cm at the sides, 30 cm behind and 30

cm above. Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), or even fire.

• Do not use the speaker's handles for suspended installation. Doing so

can result in damage or injury.

• Avoid setting all equalizer controls and faders to their maximum.

Depending on the condition of the connected devices, doing so may

cause feedback and may damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold

or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration or damage to the

internal components.

• Do not place the device in an unstable position where it might

accidentally fall over.

• Do not block the vents. This mixer has ventilation holes at the top to

prevent the internal temperature from becoming too high. In particular, do

not place the device on its side or upside down. Inadequate ventilation

can result in overheating, possibly causing damage to the device(s), or

even fire.

• Do not use the device in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Doing so may result in noise,

both in the device itself and in the TV or radio next to it.

Connections

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all volume

levels to minimum.

• For the SPEAKER jack, use only the included speaker (300S) and speaker

cable. Use of other types of speakers and cables may result in damage to

the device(s), or even fire.

Handling caution

• When turning on the AC power in your audio system, always turn on the

device LAST, to avoid speaker damage. When turning the power off, the

device should be turned off FIRST for the same reason.

• Do not insert your fingers or hands in any gaps or openings on the device

(vents,, ports, etc.).

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)

into any gaps or openings on the device (vents, ports, etc.) If this

happens, turn off the power immediately and unplug the power cord from

the AC outlet. Then have the device inspected by qualified Yamaha

service personnel.

• Do not use the device or headphones for a long period of time at a high

or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

• Do not operate the device if the sound is distorting. Prolonged use in this

condition could cause overheating and result in fire.

• Do not rest your weight on the device or place heavy objects on it, and

avoid use excessive force on the buttons, switches or connectors.

Interference From Cell Phones

Using a cell phone near the speaker system can induce noise. If this occurs,

move the cell phone further away from the speaker system.

Air blowing out of the bass reflex ports is normal, and often occurs when the

speaker is handling program material with heavy bass content.

Yamaha cannot be held responsible for damage caused by improper use

or modifications to the device.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches,

volume controls, and connectors, deteriorates over time. Consult qualified

Yamaha service personnel about replacing defective components.

• The illustrations as shown in this manual are for instructional purposes

only, and may be different from the ones on your equipment.

• The company names and product names in this manual are the

trademarks or registered trademarks of their respective companies.

IMPORTANT

Please record the serial number of this unit in the space below.

Model:

Serial No.:

The serial number is located on the bottom or rear of the unit.

Retain this Owner's Manual in a safe place for future reference.

Caution

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance with the following

code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the

coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug

which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-

and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

• This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Ser.No)

For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

(UL60065_03)

Power supply/Power cord

• Only use the voltage specified as correct for the device. The required

voltage is printed on the name plate of the device.

• Use only the included power cord.

• Do not place the power cord near heat sources such as heaters or

radiators, and do not excessively bend or otherwise damage the cord,

place heavy objects on it, or place it in a position where anyone could

walk on, trip over, or roll anything over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

Do not open

• Do not open the device or attempt to disassemble the internal parts or

modify them in any way. The device contains no user-serviceable parts.

If it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualified Yamaha service personnel.

■ Mixer

Unit: mm

■ Speaker■ General Specifications

Maximum Output Power

150 W (±10 %)/4Ω @ 10 % THD at 1 kHz (SPEAKER)

100 W/4Ω @ 1 % THD at 1 kHz (SPEAKER)

Maximum Output Level

112 dB (1 m)

Frequency Response (Nomimal output level @ 1 kHz)

-3 dB, 0 dB, +1 dB @ 20 Hz-20 kHz (MUSIC/SPEECH=MUSIC) (ST SUB OUT)

-3 dB, 0 dB, +1 dB @ 80 Hz-20 kHz (MUSIC/SPEECH = SPEECH) (ST LINK OUT)

-3 dB, 0 dB, +1 dB @ 20 Hz-20 kHz, 1 W Output (MUSIC/SPEECH=MUSIC, without

Speaker EQ) (SPEAKER)

Total Harmonic Distortion

0.5 % @ 20 Hz, 1 kHz, 20 kHz +14 dBu GAIN= nominal (ST SUB OUT, ST LINK OUT)

Hum & Noise (Equivalent Input Noise, Rs = 150Ω, MIC/LINE = MIC)

-112 dBu (CH1/2)

-65 dBu Residual output noise (SPEAKER)

Crosstalk (1 kHz)

-70 dB between input channels

Power Consumption

20 W

Weight

9.6 kg (Speaker + Powered Mixer)

Stereo Input Channel Equalization

±15 dB

HIGH 10 kHz shelving

LOW 100 Hz shelving

■ Speaker (300S)

Enclosure

2 way bass-reflex type, Polypropylene, Black

Crossover Frequency

4.0 kHz (LF: 12 dB/oct, HF: 12 dB/oct)

Frequency Range

55 Hz-20 kHz (-10 dB)

Speaker Unit

LF: 8" (20 cm) Cone

HF: 1" (2.54cm) Compression Driver

Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at

any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

PA19

NORTH AMERICA

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A.

Tel: 714-522-9011

CENTRAL & SOUTH AMERICA

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534-

013 Sao Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

EUROPE

THE UNITED KINGDOM

Yamaha Music U.K. Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen,Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH, Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Central Europe GmbH, Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Central Europe GmbH,

Branch Austria, CEE Department

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND

Yamaha Music Central Europe GmbH

Sp.z. o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-868-07-57

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH, Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A. Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Música Ibérica, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Office

Generatorvej 6A . DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Norsk filial av Yamaha Scandinavia AB

Grini Næringspark 1

N-1345 Østerås, Norway

Tel: 67 16 77 70

RUSSIA

Yamaha Music (Russia)

Office 4015, entrance 2, 21/5 Kuznetskii

Most street, Moscow, 107996, Russia

Tel: 495 626 0660

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

AFRICA

Yamaha Corporation, Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2313

MIDDLE EAST

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali, Dubai, United Arab

Emirates

Tel: +971-4-881-5868

ASIA

THE PEOPLE'S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

25/F., United Plaza, 1468 Nanjing Road (West),

Jingan, Shanghai, China

Tel: 021-6247-2211

INDONESIA

PT. Yamaha Music Indonesia (Distributor) PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto

Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu,

Seoul, Korea

Tel: 080-004-0022

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

891/1 Siam Motors Building, 15-16 floor Rama 1 road,

Wangmai, Pathumwan Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha Corporation, Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2317

OCEANIA

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST TERRITORIES IN

PACIFIC OCEAN

Yamaha Corporation, Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2313

HEAD OFFICE

Yamaha Corporation, Pro Audio & Digital Musical

Instrument Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2441

Block Diagram

(5)-5

255

455.5

275

96.3

290

160

2-M8x25

120

137