EMX5016CF Owner’s Manual 35
Reference
Specifications

■General Specifications

* All level controls are nominal, when measured. Output impedance of signal generator: 150Ω
Conditions MIN TYP MAX Unit
Maximum Output Power
(SPEAKERS)
RL=4ΩBoth channels drive, 1 kHz,
THD+N 0.5%
Rated power supplies:
120V, 230V and 240V
500
W
RL=8Ω
350
(US, AU)
320 (EU)
Total Harmonic Distortion
(THD+N)@20Hz-20kHz
ST, ST SUB, AUX, EFFECT +14dBu output into 600Ω0.3 %
REC 0dBV output into 10kΩ0.5
Frequency Response
ST, ST SUB, AUX, EFFECT 20Hz-20kHz, 1kHz output level,
GAIN at minimum level, PAD=Off,
+4dBu, RL=8Ω, 1W
–3.0 0.0 1.0
dB
SPEAKERS –3.0 0.0 1.0
EIN=Equivalent Input Noise CH1-8 MIC GAIN at maximum level,
20Hz-20kHz –128 dBu
Residual Output Noise SPEAKERS –68 dBu
ST, ST SUB, AUX –95
Crosstalk @ 1kHz Adjacent inputs –68 dB
Input to output –68
Maximum Voltage Gain @1kHz
MIC to SPEAKERS 109
dB
MIC to ST OUT 84
MIC to ST SUB OUT 80
MIC to AUX SEND (PRE) 80
MIC to AUX SEND (POST) 90
MIC to EFFECT SEND 80
MIC to REC OUT 62.2
CH 9/10-15/16 LINE to ST OUT 58
Phantom Voltage CH 1-15/16 XLR No load 48 V DC
Channel Equalizer
Maximum Variation: ±15dB
Turn over/roll-off frequency of
shelving is 3dB below maxi-
mum level.
HIGH 10kHz (Shelving)
MID (MONO) 250Hz-5kHz (Peaking)
MID (ST) 2.5kHz (Peaking)
LOW 100Hz (Shelving)
Compressor (COMP) CH1-8 On each channel 1-8: One control adjusts the Gain, Threshold, and Ratio
simultaneously.
PEAK Indicator On each channel: Indicator lights if post-EQ signal comes within 3dB of the
clipping level.
SIGNAL Indicator On each channel: Indicator lights if post-EQ signal reaches –10dB.
STANDBY Switch CH1-8 mute
Level Meter ST, PFL/AFL
Two 12-points LED level meter (PEAK, +5, +3, +1, 0, –1, –3, –5, –7, –10,
–15, –20 dB)
PEAK lights if the signal comes within 3 dB of the clipping level.
Digital Graphic Equalizer ST OUT
9-band (63, 125, 250, 500, 1k, 2k, 4k, 8k, 16kHz), ±12 dB (maximum varia-
tion)
Preset × 3, User preset × 3
Frequency Response Correction (FRC) System Pink noise/Music playback measurement mode
Feedback Suppressor (FBS) AUTO/MANUAL mode
MAXIMIZE 3-band compressor on/off
Digital Effect 2 effect processors, 16 programs each, PARAMETER control each
Foot switches (effects on/off)
Lamp XLR-3-31 type, 12 V DC between pins 2 and 3, 5 W max.
Maximum Output Power Select Switch 500W+500W, 200W+200W, 75W+75W
Power Amplifier Signal Select Switch L/R, AUX1/MONO, AUX1/AUX2
Yamaha Speaker Processing SPEAKERS Speaker EQ on/off
Power Amplifier Protection
POWER switch on/off mute
DC-fault: power supply shutdown/manual reset
Thermal/heatsink temp 90°C: output mute/auto reset
Vl limiter/RL 2Ω
Clip limiter/THD 1%: compression, Indicator × 2
Power Supply Protection Thermal/heatsink temp 100°C: power supply shutdown/manual reset
Cooling Dual variable-speed fan
Power Consumption 500 W
AC Cord Length 2500 mm
Dimensions
Height 155
mmDepth 493
Width 444
Net Weight 11 kg
<
=
>
=
<
=>
=>
=