Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha HTR-5540 Connecting the antennas, ■Connecting the AM loop antenna, models), PREPARATION, FREQUENCY STEP switch (China and General

1 59

Download 59 pages, 1.23 Mb

CONNECTIONS

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

AM loop antenna

(included)Indoor FM antenna

(included)

EO

VIDEO

TUNER

AM

ANT

GND

75Ω UNBAL.

FM

ANT

		Ground (GND terminal)
		For maximum safety and minimum
VIDEO		interference, connect the antenna GND
	FREQUENCY	terminal to a good earth ground. A good
	STEP

		earth ground is a metal stake driven into

moist earth.

■Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it.2 Press and hold the tab to insert the AM loopantenna lead wires into the AM ANT and GND terminals.3 Orient the AM loop antenna for the best reception.

PREPARATION

75-ohm/300-ohm antenna adapter (U.K. model)

1	2
	11	(7/16)
	8	(5/16)	Unit: mm
	6	(1/14)	(inch)
Open the cover of the	Cut the external sleeve
included 75-ohm/300-ohm	of the 75-ohm coaxial
antenna adapter.	cable and prepare it for
	connection.

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

FREQUENCY STEP switch (China and General

3

Lead wire

Cut the lead wire and remove it.

models)

FM/AM

50kHz/9kHz

100kHz/10kHz

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located on the rear panel) according to the frequency spacing in your area.

North, Central and South America:

4

Clamp	Clamp with
with	pliers.
pliers.
	Insert the wire
	into the slot.

Insert the cable wire into the slot, and clamp it with pliers.

5

Snap the cover into place.

FREQUENCY

STEP

100 kHz/10 kHz

Other area: 50 kHz/9 kHz

Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

17

Contents

AV Receiver SAFETY INSTRUCTIONS I CAUTION FCC INFORMATION (for US customers only) CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT We Want You Listening For A Lifetime III CAUTION CONTENTS FEATURES ■About this manual GETTING STARTED Checking the package contents Installing batteries in the remote control ■Notes on batteries CONTROLS AND FUNCTIONS Front panel 8SILENT (PHONES jack) 9STEREO/EFFECT 0PROGRAM l / h qMEMORY (MAN’L/AUTO FM) wTUNING MODE (AUTO/MAN’L MONO) Remote control Using the remote control ■Handling the remote control Front panel display 1Processor indicators SPEAKER SETUP Speakers ■Use of a subwoofer expands your sound field Speaker placement ■Main speakers Connecting the speakers ■Speaker cables ■Connecting to the SPEAKERS terminals ■MAIN SPEAKERS terminals ■REAR SPEAKERS terminals ■SUBWOOFER jack ■IMPEDANCE SELECTOR switch CONNECTIONS Before connecting components ■Connecting to digital jacks Connecting video components ■Connecting a video monitor ■Connecting a DVD player ■Connecting a digital TV/cable TV ■Connecting another video component Page Connecting audio components ■Connecting a CD player ■Connecting a CD recorder or MD recorder Connecting the antennas ■Connecting the AM loop antenna Connecting an external decoder Connecting the power supply cords ■Connecting the AC power cord ■AC OUTLETS (SWITCHED) ■VOLTAGE SELECTOR (China and General models) Turning on the power SPEAKER MODE SETTINGS ADJUSTING SPEAKER OUTPUT LEVELS Using the test tone 3 Adjust the level of the effect speakers using +/– so that it matches the level of the main speakers 4 When adjustment is complete, press TEST to stop the test tone BASIC PLAYBACK ■BGV (background video) function ■To mute the sound ■When you have finished using this unit Input modes and indications DVD AUTO ■Notes on 96-kHzsampling digital signals ■Notes on playing DTS-CD/LDs Selecting a sound field program DGTLzSci-Fi ■Selecting PRO LOGIC PRO LOGIC ■ Playing Dolby Digital Surround ■ SILENT CINEMA DSP EX or DTS ES software Spectacle ■Virtual CINEMA DSP ■Normal Stereo Reproduction DIGITAL SOUND FIELD PROCESSING (DSP) Understanding sound fields ■Recreating a sound field Hi-FiDSP programs CINEMA-DSP Sound design of CINEMA-DSP ■Dolby Digital/DTS + DSP sound field effect ■Dolby Digital/DTS + Matrix 6.1 + DSP sound field effect ■Dolby Pro Logic + DSP sound field effect ■Dolby Pro Logic CINEMA-DSPprograms ■For movie programs: No. 7 to ■For audio-videosources: No. 4 to TUNING Automatic and manual tuning ■Automatic tuning A AM 144O ■Manual tuning Presetting stations ■Automatically presetting stations (for FM stations) A1:FM ■Manually presetting stations A AM 63O kHz C :AM 63O kHz L R C3:AM 63O kHz C3:AM Tuning in to a preset station Exchanging preset stations E1:FM 87.5 MHz A5:FM 9O.6 MHz L R EDIT E1-A5 SLEEP TIMER Setting the sleep timer Canceling the sleep timer SLEEP 12Omin CONCERT HALL L R RECORDING ■Special considerations when recording DTS software ■Timer playback/recording SET MENU Adjusting the items on the SET MENU 1SPEAKER SET (speaker mode settings) ■1A CENTER (center speaker mode) ■1B MAIN (main speaker mode) ■1C REAR LR (rear speaker mode) ■1E MAIN Lv (main level mode) 2 LFE LEVEL 3SP DLY TIME (speaker delay time) 4 D. RANGE (dynamic range) 5 L/R BALANCE (balance of the main left and right speakers) control) 8 INPUT MODE (initial input mode) 9DISPLAY SET ■DIMMER 10 MEM. GUARD (memory guard) ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS ■For 5ch Stereo ADJUSTING THE DELAY TIME DELAY Changing parameter settings PRO LOGIC Music parameter descriptions ■PANORAMA ■DIMENSION TROUBLESHOOTING ■General Page Page ■Tuner ■Remote control GLOSSARY ■Dolby Surround ■Dolby Digital ■Matrix ■DTS (Digital Theater Systems) ■PCM (Linear PCM) ■Sampling frequency and number of quantized bits SPECIFICATIONS