TROUBLESHOOTING
Problem | Cause | Remedy | Refer to |
|
|
| page |
The sound suddenly | The protection circuit has been activated |
goes off. | because of a short circuit, etc. |
Check the IMPEDANCE SELECTOR switch is set to | 16 |
the appropriate position and then turn the unit back |
|
on. |
|
|
|
Check the speaker wires are not touching each other | – |
and then turn the unit back on. |
|
| The sleep timer has turned the unit off. | Turn on the power, and play the source again. | – | |
|
|
|
| |
| The sound is muted. | Press MUTE or any operation buttons on the unit to | – | |
|
| cancel a mute and adjust the volume. |
| |
|
|
|
| |
Only the speaker on | Incorrect cable connections. | Connect the cables properly. If the problem persists, | 16 | |
one side can be |
| the cables may be defective. |
| |
heard. |
|
|
| |
|
|
|
| |
No sound from the | The sound effect is switched off. | Press STEREO/EFFECT to turn it on. | – | |
effect speakers. |
|
|
| |
A Dolby Surround, Dolby Digital or DTS | Select another DSP program. | 25 – 30 | ||
| ||||
| decoding DSP program is being used with |
|
| |
| material not encoded with Dolby |
|
| |
| Surround, Dolby Digital or DTS. |
|
| |
|
|
|
| |
| A digital signal with a sampling |
| – | |
| frequency greater than 48 kHz is input to |
|
| |
| this unit. |
|
|
No sound from the | The output level of the center speaker is |
center speaker. | set to minimum. |
Raise the level of the center speaker. | 48 |
| “SOUND 1A CENTER” on the set menu | Select the appropriate mode for your center speaker. | 39 |
| is set to NON. |
|
|
|
|
|
|
| One of the | Select another DSP program. | 25 – 30 |
| has been selected (except for 6ch Stereo). |
|
|
|
|
|
|
| The source encoded with a Dolby Digital |
| – |
| or DTS signal does not have a center |
|
|
| channel signal. |
|
|
|
|
|
|
No sound from the | The output level of the rear speakers is set | Raise the output level of the rear speakers. | 48 |
rear speakers. | to minimum. |
|
|
|
|
|
|
| A monaural source is being played with | Select another DSP program. | 25 – 30 |
| program 9. |
|
|
|
|
|
|
No sound from the | “SOUND 1E BASS” on the set menu is | Select SWFR or BOTH. | 40 |
subwoofer. | set to MAIN when a Dolby Digital or |
|
|
| DTS signal is being played. |
|
|
|
|
|
|
| “SOUND 1E BASS” on the set menu is | Select BOTH. | 40 |
| set to SWFR or MAIN when a |
|
|
| source is being played. |
|
|
|
|
|
|
| The source does not contain low bass |
| – |
| signals (90 Hz and below). |
|
|
|
|
|
|
Poor bass | “SOUND 1E BASS” on the set menu is | Select MAIN. | 40 |
reproduction. | set to SWFR or BOTH and your system |
|
|
| does not include a subwoofer. |
|
|
The speaker mode settings (main, center, rear, or rear center) on the set menu does not match your speaker configuration.
Select the appropriate position for each speaker based | 39 – 40 |
on the size of the speakers in your configuration. |
|
54