TROUBLESHOOTING
Problem | Cause | Remedy | Refer to |
|
|
| page |
|
|
|
|
No sound from the | The output level of the center speaker is | Raise the level of the center speaker. | 50 |
center speaker. | set to minimum. |
|
|
|
|
|
|
| “SOUND 1A CENTER” on the set menu | Select the appropriate mode for your center speaker. | 41 |
| is set to NONE. |
|
|
|
|
|
|
| One of the HiFi DSP programs (1 to 4) | Select another sound field program. | 27 – 32 |
| has been selected (except for 5ch Stereo). |
|
|
|
|
|
|
| The source encoded with a Dolby Digital |
| – |
| or DTS signal does not have a center |
|
|
| channel signal. |
|
|
|
|
|
|
No sound from the | The output level of the surround speakers | Raise the output level of the surround speakers. | 50 |
surround speakers. | is set to minimum. |
|
|
|
|
|
|
| A monaural source is being played with | Select another sound field program. | 27 – 32 |
| program 9. |
|
|
|
|
|
|
No sound from the | “SOUND 1D BASS” on the set menu is | Select SWFR or BOTH. | 42 |
subwoofer. | set to FRNT when a Dolby Digital or |
|
|
| DTS signal is being played. |
|
|
|
|
|
|
| “SOUND 1D BASS” on the set menu is | Select BOTH. | 42 |
| set to SWFR or FRNT when a |
|
|
| source is being played. |
|
|
|
|
|
|
| The source does not contain low bass |
| – |
| signals (90 Hz and below). |
|
|
|
|
|
|
Poor bass | “SOUND 1D BASS” on the set menu is | Select FRNT. | 42 |
reproduction. | set to SWFR or BOTH and your system |
|
|
| does not include a subwoofer. |
|
|
The speaker mode settings (front, center or surround) on the set menu does not match your speaker configuration.
Select the appropriate position for each speaker based | 41 – 42 |
on the size of the speakers in your configuration. |
|
A “humming” sound | Incorrect cable connections. | Firmly connect the audio plugs. If the problem | – |
can be heard. |
| persists, the cables may be defective. |
|
|
|
|
|
The volume level | The component connected to the OUT | Turn on the power to the component. | – |
cannot be increased, | (REC) jacks of this unit is turned off. |
|
|
or the sound is |
|
|
|
distorted. |
|
|
|
|
|
|
|
The sound effect | It is not possible to record the sound |
| – |
cannot be recorded. | effect with a recording component. |
|
|
|
|
|
|
The sound field | “OPTION 2 MEM. GUARD” in the SET | Select OFF. | – |
parameters and some | MENU is set to ON. |
|
|
other settings on the |
|
|
|
unit cannot be |
|
|
|
changed. |
|
|
|
The unit does not The internal microcomputer has been
operate properly. frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage.
Disconnect the AC power cord from the outlet and | – |
then plug it in again after about 30 seconds. |
|
“CHECK SP WIRES” appears on the front panel display.
The speaker cables are short circuited. | Make sure all speaker cables are connected correctly. | – |
54