SETTING UP THE SPEAKERS

Main and rear speakers can be positioned horizontally or vertically.

Please install rubber feet included to prevent slipping movement.

Please note: Logo can rotate.

Vertical position Horizontal position

Mounting the center speaker

Place the center speaker on top of the TV, on the floor under the TV or inside the TV rack so that it is stable.

When placing the speaker on top of the TV, put the provided VelcroTM strips at two points on both the bottom of the speaker and on top of the TV to prevent the speaker from falling.

Notes

Do not place the speaker on top of the TV whose area is smaller than the bottom area of the speaker. The speaker may fall and might cause personal injury.

Though this speaker is a magnetically shielded type, there may be some influence on a TV picture depending on the type of TV or the placement of the speaker. In such a case, place the speaker apart from TV so that there is no influence on TV picture.

SPEAKER PLACEMENT

This speaker is designed to be used as a main, center, surround or effects speaker

-Main speaker placement should be separated by distance of 6-10ft. If they are placed too close together, there will be a reduction in the stereo effect.

Conversely. If placed too far apart, the so called "middle-omission"effect will occur and the vocal center fill will be lost. Height of the speaker should be at least at ear level.

-Center channel speakers should be placed centered above or below the TV.

-Surround speakers should ideally be placed behind the listening area. At least as far apart as the main speakers and up to 2 additional feet apart per side. The height of the speaker should be at a minimum of ear level or preferably somewhat higher.

 

 

 

 

 

 

 

 

Center Channel Speaker

 

 

 

 

 

 

 

 

 

 

 

Left Main Speaker

 

 

 

Right Main Speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 10 feet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

up to approx

 

 

 

LISTENING AREA

 

 

 

 

 

up to approx

2 feet more

 

 

 

 

 

 

 

 

 

 

 

2 feet more

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Left Surround Speaker

 

 

 

Left Surround Speaker

SPECIFICATIONS

Mounting the main and rear speaker

Please place rubber feet as shown in the diagram

 

Model

NS-AP1400

prior to mounting the speakers on the wall.

 

 

Center Speaker

NS-AP1400C

 

 

 

 

 

Type

2-way Acoustic Suspension

 

 

 

 

 

Speaker: Woofer

Dual 2 3/4" Pulp cone and Rubber surround

 

 

 

 

 

Speaker: Tweeter

1/2" Balanced dome

 

 

 

 

 

Frequency Range

90Hz ~ 50kHz (-10dB)

 

Min.

 

 

Impedance

6 ohms

 

20mm

 

 

Nominal Input

30w

6mm

 

 

 

 

 

 

 

 

 

Maximum Input

100w

 

 

 

 

 

Sensitivity (dB/2.83v. 1m)

80dB

 

 

 

Fasten screws into a film wall or wall

 

Crossover Frequency

4,500Hz

 

 

 

 

Dimension (H×W×D)

3 5/8"×9 7/8"×4 3/8" (92×250×111mm)

 

 

 

support as shown in the figure, and hang

 

 

 

 

 

Weight

2,51lbs(1.14kg)

 

Min.

the holes of the mounting bracket on the

 

Finish

Silver and Black

 

 

 

 

 

20mm

protruding screws.

 

Magnetic Shielding

Yes

6mm

 

 

 

 

 

 

 

 

Make sure that the screws are securely

 

Main and rear

NS-AP1400S

 

 

 

 

Type

2-way Acoustic Suspension

 

 

 

caught by the narrow sections of the “key

 

 

Min.

 

Speaker: Woofer

2 3/4" Pulp core and Rubber surround

 

 

 

20mm

hole” opening. Main and rear speakers can

 

Speaker: Tweeter

1/2" Balanced dome

6mm

 

 

 

(Available at the

be mounted horizontally or vertically.

 

Frequency Range

90Hz ~ 50kHz (-10dB)

 

Impedance

6 ohms

Tapping screw

 

 

 

 

hardwarestore)

 

 

Nominal Input

30w

WARNING

 

 

Maximum Input

100w

 

 

Sensitivity (dB/2.83v.ln)

80dB

Each speaker weight 1.76 lbs (0.80kg). Do not mount them on thin plywood or soft

 

Crossover Frequency

4,000Hz

 

Dimension (H×W×D)

6 5/8"×3 5/8"×4 1/8"(168×92×106mm)

surface material. If mounted, the screw may come out of the flimsy surface and the

 

 

Weight

1.76 lbs (0.80kg)

speakers may fall. This damages the speakers or causes personal injury.

 

Finish

Silver and Black

 

Magnetic Shielding

Yes

Do not install the speakers to a wall with nails, adhesives, or any other unstable

 

 

Accessories

100" Bulk Speaker Wire

hardware.

 

 

 

 

 

3/83/32" Rubber foot 16pcs

To avoid accidents resulting from tripping over loose speaker cords, fix them to the wall.

 

 

1 17/32"×2" VelcroTM 2pcs

Secure installation is the purchaser’s responsibility.

2

*Specifications subject to change without notice due to product improvements.