Yamaha NS-BP100, NS-BP110 PRECAUTIONS, ACCESSORIES, PLACING THE SPEAKERS, SPECIFICATIONS, 2 En, ATTACHING THE FRONT COVER, CONNECTION TO YOUR RECEIVER, ATTACHING THE SPEAKER STANDS

English

PRECAUTIONS

•Install the speakers in a cool, dry, clean, stable and horizontal place.

•To avoid electric shock, fire, injury, damage to the speakers, and discoloration of the cabinet, install away from windows, heat sources, sources of excessive vibration, dust, moisture, cold, rain, water, falling objects, noise sources (transformers, motors, etc.) and direct sunlight.

•Do not insert a hand or object into the port or pick up the speaker by holding the port, as it may cause personal injury or damage to the speaker.

•Any time you note distortion, reduce the volume control on your receiver to a lower setting. Never allow your receiver to be driven into “clipping”. Otherwise the speakers may be damaged.

•When using a receiver with a rated output power higher than the nominal input power of the speakers, care should be taken never to exceed the speakers’ maximum input.

•Do not attempt to clean the speakers with chemical solvents as this might damage the finish. Use a clean, dry cloth.

•Do not attempt to modify or fix the speakers. Contact qualified Yamaha service personnel when any service is needed. The cabi- net should never be opened for any reasons.

•Secure placement or installation is the owner’s respon- sibility. Yamaha shall not be liable for any accident caused by improper placement or installation of speak- ers.

ACCESSORIES

Check that the following items are included.

Speaker cable (2 m) x 2 / Front cover x 2

ATTACHING THE FRONT COVER

To attach the front cover, line up the three holes on the inner surface of the cover with the three corresponding pegs on the speaker and push gently.

Note

When the cover is removed, be sure not to touch the speaker units with your hands or to exert excessive force with tools.

CONNECTION TO YOUR RECEIVER

BEFORE MAKING CONNECTIONS, MAKE SURE THAT THE RECEIVER IS SWITCHED OFF.

When this unit is connected to the receiver, refer also to the owner’s manual supplied with the receiver.

See page 1 for the connection method.

2 En

PLACING THE SPEAKERS

•Place the speakers on a sturdy, vibration-free surface. You may not be able to obtain good bass quality when the speakers are placed directly on the floor. Put a block, etc. under the speakers.

•Better stereo images will be obtained when the speakers are slightly angled in towards the listening position.

Note

Placing this unit too close to a CRT TV set might happen impair picture color or create a buzzing noise. Should this happen, move the speaker away from the TV set.

ATTACHING THE SPEAKER STANDS

NS-BP110 only

You can also use the screw holes on the bottom of the NS-BP110 for installing the speakers on commercially available speaker stands.

A screw with a diameter of 4 mm can be used(Hole depth: 10 mm, 3/8”)

•Before installing, please refer to the instruction manual of the speaker stand.

SPECIFICATIONS
Type ..............................................	2-way bass-reflex speaker system
	Non-magnetic shielding Type
Driver...........................................................	10 cm (4”) cone woofer
	2.5 cm (1”) balanced dome tweeter
Impedance....................................................................................	6Ω
Frequency Response.................................	60 Hz to 50 kHz (-10 dB)
	100 kHz (-30 dB)
Nominal Input Power ...............................................................	30 W
Maximum Input Power..............................................................	90 W
Sensitivity .................................................................	84 dB/2.83 V/m
Crossover Frequency ................................................................	8 kHz
Dimensions (W x H x D)
<NS-BP100> ..................................................	123 x 192 x 294 mm
	(4-13/16” x 7-9/16” x 11-9/16”)
<NS-BP110> ..................................................	123 x 192 x 296 mm
Weight	(4-13/16” x 7-9/16” x 11-5/8”)
<NS-BP100> ..................................................	2.1 kg (4 lbs. 10 oz.)
<NS-BP110> ....................................................	2.3 kg (5 lbs. 1 oz.)

*Specifications are subject to change without notice due to product improvements.

*Care should be taken not to exceed the input power values noted above.