CONTROLS AND FUNCTIONS

Front panel

1

2 3 4 5 6

7

8 9 0 A B C D E

ZONE 2 ON/OFF

FM/AM

l TUNING/CH h

 

 

XM/ANT

 

PURE DIRECT

CD DIRECT AMP

 

 

 

 

ZONE CONTROL

EDIT

MEMORY

TUN MODE/DISP

 

 

SEARCH MODE

MAN'L/AUTO FM

AUTO/MAN'L

 

MASTER

SPEAKERS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16

A/B/C/D/E

 

 

1

 

2

3

 

4

5

 

6

7

 

8

20

12

 

A

B

 

 

 

 

 

 

VOLUME

 

 

 

 

CATEGORY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26

8

ON OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT

 

 

REC OUT

 

BASS

 

TREBLE

 

BALANCE

DISPLAY

LOUDNESS

 

 

MAIN ZONE

 

 

PHONES

 

 

CD

 

0

 

 

0

 

 

0

 

 

FLAT

40

4

 

 

 

MD/TAPE

XM

1

1

 

1

1

 

1

1

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–30dB

 

 

 

 

 

 

VCR

 

TUNER

2

2

2

 

2

2

 

2

2

 

10

 

 

ON/OFF

 

 

DTV/CBL

 

PHONO

3

3

3

 

3

3

 

3

3

 

9

60

2

 

 

 

 

DVD

 

 

4

4

4

 

4

4

 

4

4

 

8

∞

 

 

 

 

 

 

 

 

– 5

5 +

 

– 5

5 +

 

L 5

5 R

 

5

7

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

-dB

 

 

 

 

(U.S.A. model)

F G H I

J

K

L

M N

1 MASTER ON/OFF

 

4 ZONE 2 ON/OFF

INTRODUCTION

Press inward to the ON position to turn on the power of this unit. Press again to release it outward to the OFF position to turn off this unit.

See page 17 for details.

Note

Even when this unit is turned off, this unit consumes a small amount of power to preserve the memory.

Turns on Zone 2 or set it to the standby mode. When Zone 2 is turned on, signals are output at the ZONE 2 OUT jacks.

Note

This switch is operational only when MASTER ON/OFF is pressed inward to the ON position.

5ZONE CONTROL
Memory back-up

The memory back-up circuit prevents the stored data from being lost. However, the stored data will be lost if the power cord is disconnected from the AC wall outlet for more than one week.

2MAIN ZONE ON/OFF

Turns on Main Zone of this unit or sets it to the standby mode.

See page 17 for details.

Notes

Press to control the input source of Zone 2.

Notes

•This button is operational only when Zone 2 is turned on.

•When you press this button, the ZONE 2 indicator flashes in the front panel display for approximately 5 seconds. Select the input source of Zone 2 while the indicator is flashing.

•You can select the preset station or channel when TUNER or XM is selected as the input source of Zone 2.

6Remote control sensor

Receives infrared signals from the remote control.

• This switch is operational only when MASTER ON/OFF is

Note

 

 

 

pressed inward to the ON position.

Switch the remote control ID between ID1 and ID2 when using

• In the standby mode, this unit consumes a small amount of

multiple YAMAHA receivers or amplifiers (see pages 9, 39 and

power to receive infrared signals from the remote control.

40).

 

3 SPEAKERS A/B7 Front panel display

Turns on or off the speaker set connected to the

Shows information about the operational status of this

SPEAKERS A and/or SPEAKERS B terminals on the rear

unit.

panel each time the corresponding button is pressed (see

 

page 18).

 

3