87
Operations in the SELECTED CHANNEL section
7
Operations in the SELECTED CHANNEL section
LS9-16/32 Owner’s Manual
Making dynamics settings
To operate the dynamics of the currently selected channel,
use the SELECTED CHANNEL section [DYNAMICS 1]/
[DYNAMICS 2] encoder, and the DYNA1/DYNA2 field
of the SELECTED CH VIEW screen.
The DYNA1/DYNA2 field of the SELECTED CH VIEW
screen contains the following items.
1DYNA1/DYNA2 popup buttons
These buttons access the DYNAMICS 1/DYNAMICS 2
popup window, where you can make detailed settings for
dynamics.
BTHRESH knob
This indicates the setting of the threshold parameter of a
gate or compressor. To adjust the value, use the
SELECTED CHANNEL section [DYNAMICS 1]/
[DYNAMICS 2] encoder. (Alternatively, move the cursor
to the knob and operate the dial or the [DEC]/[INC] keys.)
CDYNAMICS ON/OFF button
These buttons turn dynamics processors 1/2 on/off.
DOVER indicator
This will light if the output level of the dynamics reaches
the overload point.
ELevel meter
This displays a bar graph indication of the signal level
being input to the dynamics (on=green, off=gray) and the
amount of gain reduction (orange). The threshold setting
is shown as a vertical line.
FParameter knobs
These knobs indicate the values of parameters other than
threshold.
To operate the dynamics, turn the DYNAMICS ON/OFF
button on, and use the SELECTED CHANNEL section
[DYNAMICS 1]/[DYNAMICS 2] encoders to adjust the
threshold parameters. (Alternatively, move the cursor to
the DYNA1/DYNA2 field, and operate the dial or the
[DEC]/[INC] keys.)
To make detailed dynamics settings, move the cursor to
the DYNA1/DYNA2 popup button or the DYNA1/
DYNA2 field, and press the [ENTER] key to access the
DYNAMICS 1/DYNAMICS 2 popup window. (For
details on the popup window p. 117)
Making HPF/EQ settings
To operate the HPF/EQ of the currently selected channel,
use the SELECTED CHANNEL section EQ encoders,
and the EQ field of the SELECTED CH VIEW screen.
The EQ field of the SELECTED CH VIEW screen con-
tains the following items.
1EQ popup button
This button accesses the ATT/HPF/EQ popup window,
where you can make detailed HPF/EQ settings.
BEQ ON/OFF button
Switches the EQ on/off.
CHPF ON/OFF button
Switches the HPF on/off.
DHPF FREQ knob
Indicates the cutoff frequency of the HPF.
EOVER indicator
This will light when the post-EQ signal reaches the over-
load point.
FQ/F/G knobs
These knobs indicate the Q, F (center frequency), and G
(amount of boost/cut) settings for each band (LOW, L-
MID, H-MID, and HIGH).
To operate the EQ, switch the EQ ON/OFF button on, and
use the EQ [Q], EQ [FREQUENCY], and EQ [GAIN]
knobs of the SELECTED CHANNEL section to adjust the
Q, center frequency, and the amount of boost/cut. (Use the
EQ [HIGH], EQ [HIGH MID], EQ [LOW MID], and EQ
[LOW] keys to select the band you want to operate.)
Alternatively, move the cursor to the knobs of the EQ field
in the screen, and use the dial or the [DEC]/[INC] keys.
To make detailed EQ settings, move the cursor to the EQ
popup button or the knobs of the EQ field, and press the
[ENTER] key to access the ATT/HPF/EQ popup window.
(For details on the popup window p. 115)
• The DYNA 2 field of the SELECTED CH VIEW screen and the
[DYNAMICS 2] encoder of the SELECTED CHANNEL section are
valid only if an input channel is selected.
NOTE
2
1
34
6
5
• If you’ve turned on POPUP APPEARS WHEN PRESSING
KNOBS in the PREFERENCE popup window (
p. 194), you can
also access the above popup window by pressing the SELECTED
CHANNEL section [DYNAMICS 1]/[DYNAMICS 2] encoder.
HINT
6
2
5
1
4
3