MAINTENANCE

1.Engine oil level: Check daily with engine cold and on a flat surface. Remove the dipstick and wipe clean. Reinsert the dipstick all the way. Remove the dipstick and check oil level. If oil level is low remove oil fill cap and add oil. Use engine manufacturers specs for type of oil.

2.Pump drive belt compartment: Stop engine and remove key. Tilt seat forward and lift rubber flap. Clean all debris from inside. Inspect rubber flap for proper fit and replace if needed. NOTE: Cleaning may need to be done more frequently in dry conditions.

3.Mower blades: Stop engine and remove key. Lift deck into the transport position and in- spect blades. Sharpen or replace as needed. Check daily or more often if needed. The machine requires more power with dull blades and gives a poor cut. If blades get bent, replace them. Blades shouldn’t have any notches from hitting objects. The air foil on top of the blade should be sufficient to raise the grass for cutting. If blades are in good condition, sharpen at an angle of 22 to 28 degrees about 2-1/2 inches in from the tips. Note: After sharpening, check blades for proper balance, if needed correct balance to prevent excessive vibration.

4.Safety interlock system: Check daily and never operate the mower if this system is not functioning properly. The starter should crank only when the operator is in the seat, the park brake set, blades off and the motion control levers in the neutral slots. If the mower starts with any of these controls on or in an operating position, turn the mower off and repair the system immediately.

5.Hardware: Stop engine and remove key thoroughly inspect the entire machine for any missing or loose hardware. Check daily.

6.Air cleaner: Stop engine and remove key. Remove plastic cover and loosen wingnut on the air cleaner. Remove the foam pre-cleaner and wash or replace if needed. Inspect paper filter and replace if dirty. Check every 25 hours, daily if in very dirty conditions. Fuel efficiency, engine RPM, and available power goes down rapidly if the air filter is dirty. Prolonged effects could damage the engine.

7.Engine oil: Change oil to manufacturers specifications. Stop engine and remove key. Drain oil when engine is warm. Thoroughly clean around cap before removing. Remove oil drain cap from the end of drain hose located at the right rear of unit allow to drain and replace drain cap. Remove oil filter and replace. Put a light coat of clean oil on the filter gasket before installing. Fill engine with oil using manufacturers specs, see specification sheet. The factory

uses Quaker State Super Blend 10w-30. Start engine and idle slowly to allow the oil to recoat the interior of the engine and then inspect for leaks.

8.Hydraulic oil: Check daily. Stop engine and tilt seat forward.Thoroughly clean around cap. Remove cap. Oil level should be 1/4” to 1” below the neck of the tank. If not, add oil. NOTE: Use

13

Page 12 Page 14
Page 13
Image 13
Yazoo/Kees ZKW52233, ZKHP52233, ZKH61253, ZKHP61253, ZKHP52253, ZKH52253, ZKH52223, ZKW61233 Maintenance
Page 12 Page 14

ZKW61233, ZKH52223, ZKW52233, ZKH52253, ZKHP52253 specifications

The Yazoo/Kees ZKHP52233, ZKHP52253, ZKW52233, ZKH61253, and ZKH52253 stand out in the landscape of compact and efficient commercial mowers. These models are designed to meet the demanding needs of landscape professionals, offering a combination of power, precision, and adaptability.

One of the main features of these mowers is their robust engine performance. Each model is equipped with powerful engines that provide consistent torque and speed, enabling them to tackle dense grass and tough terrain efficiently. The engines are engineered for reliability, ensuring that they can operate under heavy loads without compromising performance.

The ZKHP52233 and ZKHP52253 model lines showcase a high-performance hydrostatic drive system. This technology allows for smooth acceleration and responsive handling, making it easier for operators to navigate tight spaces and challenging landscapes. The hydrostatic transmission also contributes to reduced wear and tear, prolonging the lifespan of the mower.

The cutting decks across these models are designed for superior performance. The ZKHP52233 and ZKW52233 feature adjustable cutting heights, providing versatility for different types of grass and landscaping needs. The cutting width is optimized for efficient mowing, allowing operators to cover larger areas in less time while ensuring a clean, even cut.

Ergonomics play an essential role in the design of these mowers. The operator's station is thoughtfully crafted to minimize fatigue during long working hours. Features such as adjustable seats, intuitive controls, and vibration-reducing components enhance user comfort. The ZKH61253 model takes this a step further with a more spacious platform, accommodating operators of various sizes comfortably.

Additionally, the durability of these mowers is notable. Constructed with high-quality materials and reinforced frames, they are built to withstand the rigors of commercial use. The rust-resistant components ensure longevity even when exposed to various weather conditions.

In terms of maintenance, Yazoo/Kees has implemented user-friendly features that simplify regular upkeep. Accessible service points and easy-to-replace parts allow for quick maintenance, ensuring that these mowers run at peak performance day in and day out.

Overall, the Yazoo/Kees ZKHP52233, ZKHP52253, ZKW52233, ZKH61253, and ZKH52253 embody a perfect blend of power, efficiency, and user-centric design. These mowers are tailored to meet the needs of commercial landscapers, providing the tools necessary to excel in a competitive environment while ensuring the highest standards of performance and reliability.
Top Page Image Contents