Manuals / York / Household Appliance / Air Conditioner

York CU060 - 300 manual Description, General

Models: CU060 - 300

1 28
Download 28 pages 58.31 Kb
Page 3
Image 3

271846-YTG-B-0208

DESCRIPTION

These units are completely assembled, piped, wired, charged and tested at the factory and are shipped ready for immediate installation. Only the power supply wiring, the thermostat wir- ing, the condenser water piping, the condensate drain piping and the ductwork are required to complete the installation.

Units include a one-year limited warranty on all replacement parts and a five-year limited warranty on each compressor.

APPLICATION FLEXIBILITY

These “cooling only” units can be applied with:

1.Cooling towers.

2.Well or surface water providing the temperature and the GPM of the water meet the application limitations of the unit.

3.Brackish or salt water and a secondary heat exchanger. They can be installed:

1.Within the conditioned space as “free standing” units without any ductwork. Supply air plenum and return air grille accessories are available for these freestanding applications.

2.In an equipment room with both supply and return air ductwork

GENERAL

Horizontal (CH) units are designed for suspended mounting. HWC models are shipped with ‘straight-through’ evaporator fan discharge as standard. Airflow orientation is field convert- ible to side discharge. Vertical (CU) units are designed for free-standing floor mounting. All units are completely factory wired and pre-piped. Water supply, water outlet, and conden- sate drain connections are via female pipe thread fittings.

All models 5 -25 tons ship as factory-charged unitized pack- ages. The 5 -15 ton units may be field split between the evap- orator /compressor section and the upper blower section; installation is possible through standard height doorways and elevators. All packages are designed for free-standing floor mounting. All models are shipped with vertical evaporator fan discharge as standard. Units are completely factory wired and piped. Dual circuit models feature internally manifolded condensers.

CABINET

All cabinets are completely constructed of 18 Ga. corrosion resistant "Galvalume" coated steel. The entire unit interior (both evaporator and condensing section) is insulated with 1/2" thick, 2 lbs. density insulation. Service panels are equipped with lifting handles for ease of removal and han- dling. Duct flanges for return air intake and evaporator dis-

charge are provided with the unit, for field installation. Duct flange on CU240 & CU300 evaporator return is incorporated into the filter frame.

REFRIGERATION CIRCUITS

All models utilize "Scroll" type hermetic compressors. Com- pressors are mounted on rubber isolators to minimize vibra- tion transmission. Internal overload protection is provided.

External high pressure and low pressure cutout switches are included in each compressor control circuit. The 5 ton units have a single refrigeration circuit. The 8 -20 ton units feature two independent refrigeration circuits. The 25 ton unit has three independant refrigeration circuits. Each refrigeration cir- cuit includes an adjustable thermal expansion valve (with external equalizer), liquid line filter drier, sight glass/moisture indicator, and service gauge ports.

The evaporator coils are constructed of internally enhanced copper tubes mechanically bonded to rippled aluminum plate fins. The evaporator coil is employed in a draw-through con- figuration, and features inter-laced circuiting. Large evapora- tor coil face area minimizes potential water blow-off.

The high-efficiency tube-in-tube condensers feature a convo- luted inner tube design for optimum performance. Standard models feature a copper inner tube surrounded by a steel outer tube, and carry a 400 psig working pressure rating.

INDOOR FANS

Forward curved, double inlet and double width centrifugal blowers are used for evaporator air movement. Large diame- ter wheels are employed to provide required airflow perfor- mance at minimum rpm and noise levels. Blower wheels are fabricated of galvanized steel. Blowers employ solid steel shafts, supported in permanently lubricated ball bearings. All blowers are belt driven. Variable-pitch motor sheaves allow for field adjustment of blower rpm.

ELECTRICAL/CONTROLS

All units are completely factory wired with all necessary con- trols. Manual reset protection is provided on evaporator blower motors. A manual reset circuit is also provided on each compressor control circuit in the event of high/low pres- sure cutout. A 24 volt control circuit, with oversize trans- former, is provided for field connection. Units are designed to operate with conventional thermostat control interface.

FILTERS

All models are shipped with 2 inch thick medium-efficiency throwaway filters factory installed. Filters are accessible from either front or right side on 5-15 ton models. The CU240 and CU300 filter rack is external to the cabinet (shipped loose).

Johnson Controls Unitary Products

3

Page 2 Page 4
Page 3
Image 3
York CU060 - 300 manual Description, General
Page 2 Page 4

CU060 - 300 specifications

The York CU060-300 is a robust and high-efficiency chiller designed to meet the demanding cooling needs of various commercial applications. This unit is recognized for its superior performance and reliability, making it a preferred choice for facilities requiring substantial cooling capacity. The CU060-300 features a cooling capacity range that is particularly suited for medium to large-scale industrial and commercial installations.

One of the standout features of the York CU060-300 is its advanced scroll compressor technology. This innovative feature ensures efficient operation, reducing energy consumption while providing consistent cooling performance. The scroll compressor also contributes to a quieter operation, enhancing the comfort of the surrounding environment. This is particularly crucial in settings like offices, schools, and healthcare facilities where noise levels need to be kept to a minimum.

In terms of efficiency, the CU060-300 is designed with a focus on energy-saving technologies. It incorporates a high-efficiency heat exchanger that maximizes thermal transfer, allowing the unit to operate effectively even in challenging environmental conditions. With a high SEER (Seasonal Energy Efficiency Ratio) rating, the chiller significantly lowers operating costs and supports sustainability initiatives by minimizing the carbon footprint.

The CU060-300 is equipped with advanced controls that streamline operation and enhance functionality. These controls provide intuitive interfaces for monitoring and managing system performance, allowing for real-time adjustments to optimize energy use. Additionally, the unit can be integrated into building management systems, enabling centralized monitoring and control for improved operational efficiency.

Reliability is another hallmark of the York CU060-300. The robust construction and high-quality materials contribute to a long operational life and reduced maintenance requirements. The chiller is designed to withstand varying environmental conditions, ensuring reliable performance year-round.

Moreover, the unit’s design incorporates environmental considerations, as it uses refrigerants that align with current regulatory standards to minimize environmental impact. This commitment to sustainability is increasingly important in today’s eco-conscious market.

In summary, the York CU060-300 stands out for its energy efficiency, advanced technologies, and reliability. Its combination of high-performance features makes it an ideal solution for those seeking a durable and effective cooling system for their commercial and industrial needs.