Zenith P60W26 PC Mode Adjustments

23

Safety instructions Monitor Overview Basic operation Sleep timer Picture & Sound Special features OthersConnections

1

3

PC Mode Adjustments

Press the up/down button to select SCREEN

and then press the vol ( G) button.

If picture needs to be adjusted more after Auto adjustment, you can

manually adjust the image position and PHASE.

-Automatically adjusts picture position and eliminates any image shaking.

Auto adjustment

READY

2Press the up/down button to select

AUTO.CONFIG. and then press the vol

( G) button.

•When AUTO.CONFIG. has finished, "OK" will be shown on screen.

• If the position of the image is incorrect, try Auto adjustment again.

LANGUAGE

G

CAPTION

G

AUTO OFF

G

SCREEN

G

RGB-OUTPUT

G

AUTO.CONFIG.

G

V-POSITION

G

H-POSITION

G

PHASE

G

RESET

G

G

TO SET

AUTO.CONFIG.

LANGUAGE G

ARC G

SCREEN G

TRANSPARENCY G

PIP/DW G

SET ID G

COLOR TEMP. G

G

TO SET

SPECIAL

SCREEN

Tips

•If the image is still not correct, your Monitor is functioning properly but needs further

adjustment.

Press the menu button and then press the up/down button

to select SPECIAL menu.

Press the vol ( G) button.

menu up

down

vol

up

down

vol

up

down

vol

Contents

Main PLASMA DISPLAY PANEL 206-03784 P/NO : 3828VA0277V (NP00KB) OWNERS MANUAL WARNING TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOTEXPOSE THIS PROD- UCT TO RAIN OR MOISTURE. The explanation about colored dots may be present on PDP screen The explanation about noise of 60" PDP Earth wire should be connected. Table of Contents WARNINGS WARNING: CAUTION: COMPLIANCE: FCC NOTICE SAFETY INSTRUCTIONS Important safeguards for you and your new product 1. Read Instructions 2. Follow Instructions 3. Retain Instructions SAFETY INSTRUCTIONS 11. Power Sources 12. Power-Cord Polarization 13. Power-Cord Protection 14. Outdoor Antenna Grounding 19. Servicing 20. Damage Requiring Service 21. Replacement Parts 22. Safety Check 23. Wall or Ceiling Mounting Front Panel Controls <Front Panel Controls> <Back Panel> Connection Panel Overview Remote Control Key Functions/Accessories Accessories Monitor Installation Wall Mount Installation Desktop Pedestal Installation VCR Setup (+)( ) (+)( ) AUDIO (+) ( ) (+)( ) RS-232C To watch VCR video/pc S-VIDEO.) Insert a video tape into the VCR and press the PLAYbutton on the VCR. See VCR owners manual. Cable TV Setup To watch cable TV R L AUDIO VIDEO (+)( ) (+)( ) External AV Source Setup DVD Setup How to connect a DVD (digital video disk player) How to use Component Input ports Connect DVD player jacks to Monitor Component input jacks as indicated below. Back panel of a DVD player DTV Setup or Back panel of a digital SET-TOPBOX R B PC Setup How to use Setup Instructions to Connect a PC to your Monitor Use the video/pc Monitor Image Display Specifications PC Mode Feature Check (Overview) vol vol menu Press the enter button to remove menus. 1 Press the up/down button to select menus. Each press will cycle through the different menus as shown below. <Picture menu> <Sound menu> PC Mode Adjustments -Automatically adjusts picture position and eliminates any image shaking. Press the up/down button to select Auto adjustment AUTO.CONFIG. and then press the vol 1 Adjusting horizontal / vertical position manually -Only adjust V-POSITIONand H-POSITION in DTV or component 480p/720p/1080i. Press the up/down button to select TION or H-POSITION and then press the vol 1 Connections Press the vol button to adjust phase and then press the enter button. The adjustment range of PHASE is 0 ~ 63. Picture Phase Adjustments Picture In Picture (PIP) function Watching the PIP (Picture in Picture) Press the pip button. Each time you press pip or vol button, you can change the PIP size as below. PIP[S] PIP [L] OFF Selecting the source input signal Press the input select button in PIP mode. Moving the Sub (inset) picture Press the position button in PIP mode. 1 Use the up/down button to select SELECT and then press the vol ( G) button. Each time you press up/down button, you toggle between SOUND [M] or SOUND [S]. Selecting PIP sound options Twin picture mode Press the twin picture button. Twin picture mode Selecting a source for the Twin picture Press the input select button in TWIN PICTURE mode. Using the remote control Notes for using the remote control Turning on the Monitor Turning on the Monitor just after installation Turning on the Monitor (power cord is still connected) Selecting language for the menus LANGUAGE and then press the Press the enter button. Press the up/down button to select the desired language. Press the menu button. Press the up/down button. Checking features Press the enter button to exit. <Picture menu> <Sound menu> -Use the remote control to make adjustments. - Select VIDEO input source Setting Sleep Timer Sleep Timer turns the Monitor off after a preset time APC (Auto Picture Control) Press the apc button. Press the apc or vol buttons to select your desired picture condition. Auto picture control Use APC to set the Monitor for the best picture appearance Example : Changing the contrast. CONTRAST and then press the vol ( G)button. Adjusting picture appearance - PIP and Twin picture inset settings are not adjustable. DRP (Digital Reality Picture) DRP improves image outlines in dark screens. Press the enter button. DRP and then press the vol ( G)button. CLEAR or SOFT.APC G Adjusting sound Manual setting Example : Adjustment treble Use the up/down button to select TREBLE and then press the vol ( G)button. 1 2 sound setup. Safety instructions Monitor Overview Connections Basic operation Sleep timer Special features Others Picture & Sound AVL (Auto Volume Leveler) This feature maintains an equal volume level; even if you change channels. Press the enter button to remove menu. AVLand then press the vol ( G) button. Using Still function Press the freeze button. To return to normal viewing, press the freezebutton again. Use the up/down button to select SCREEN and then press the Using the screen options - This function works only in the video mode. - Adjusting OSD Transparency To make the menus clear or opaque Press the enter button to remove menu. TRANSPARENCYand then press the Press the vol buttons to adjust OSD transparency. 1 Adjust GREEN and BLUE in the same way. The adjustment range of RED, GREEN and BLUE is -5 ~ +5. COLOR TEMP.and then press the Press the up/down button to select Setting picture format Press the ratio button to select a desired picture format. - How to connect external control equipment system) and control the Monitors functions externally. Monitor Rear Connections Panel AUDIO RL Type of connector : D-Sub 9-pin male RS-232C configurations 1 Use this function to specify a monitor ID number. The adjustment range of SET ID is 1 ~ 99. 2 SET ID Communication Parameters Command Reference List - OK Acknowledgement 01. Power (Command:p) 02. Input select (Command:i) 03. Aspect Ratio (Command:r) 04. Screen mute (Command:m) 05. Volume mute (Command:w) 06. Volume control (Command:v) 07. Contrast (Command:k) 08. Brightness (Command:b) 09. Color (Command:c) 10. Tint (Command:t) 12. OSD select (Command:d) 13. Abnormal state (Command:a) 14. PIP / DW (Command:z) 15. PIP input select (Command:e) 16. PIP sound select (Command:u) 18. Change into Remote control adjustment mode (Command:j) 17. PIP position (Command:x) Page Maintenance Cleaning the screen Cleaning the cabinet Extended absence Troubleshooting check list Product specifications