OPT10, How you can maintain the best control | Zenoah BCZ2601S

OPT10

English

12. Optional blade usage

3.How you can maintain the best control:

a.Keep a good, firm grip on the unit with both hands. A firm grip can help neutralize bounce. Keep your right and left hands completely around the respective handles.

b.Keep both feet spread apart in a comfortable stance and yet braced for the possibility that the unit could bounce. Do not overreach. Keep firm footing and balance.

■MAINTENANCE BLADE

• Check the blade and the fasteners for looseness, cracking, or bending.

• Check the cutting edges and reform with a flat file.

(A)22, 24-tooth blade

(B)8-tooth blade

(C)4-tooth blade

Point (OPT10) :

1.Keep the end corner sharp.

2.Round the root of the edge, using round file.

3.Do not use water when using a grinder.

IMPORTANT

•It is recommended that filing should be done by professionals.

•Especially regarding filing the 22,24-tooth blade, Leave it to the professionals.

■TRANSPORTING THE UNIT

•When you finish cutting in one location and wish to continue work in another spot, turn off the engine, and lift up the unit and carry it paying attention for the blade.

•Never forget to place the protective cover over the blades.

•When transporting the unit over long distances, detach the blade fix the unit by ropes.

50

Image 50

Zenoah BCZ2601S manual OPT10, How you can maintain the best control, Maintenance Blade, Transporting the Unit

Contents

OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido Specifications Parts location Especificaciohes Emplacement des pieces Situación de las piezasFiche technique Symbols on the machine Position Emplacement Posición Working Circumstance For safe operationWorking Condition Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail Precauciones Working Plan Before Starting the Engine DE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN Marche Using the Product Starting the Engine Utilisation DE LA Machine USO DEL Producto Demarrage DU MoteurArranque DEL Motor Maintenance If Someone Comes SI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien Mantenimiento Transportation Handling FuelRefill after cooling the engine Manipulación DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriado Set up Assemblage Montaje Recommended Mixing Ratio Gasoline 50OIL When using RedMax/ZENOAH genuine oilFuel Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 Aceite For Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA Unidad Fuel Combustible SIN Aceite Gasolina Cruda Cutting head will start rotating upon the engine starts OperationOP1 OP2 Starting Engine OP3 Fonctionnement Uso Palanca del estrangulador 2 cerrar OP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 Stopping Engine OP3 Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador Travail DE Coupe Utilisation DE LA Tete a FIL Adjusting the Line Length OP7 Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA Línea Maintenance Maintenance Chart Tableau D’ENTRETIEN EntretienMantenimiento Tabla DE Mantenimiento AIR Filter MA1 MA2 MA3Refilling Trimming Line MA1 Fuel Filter Filtre a Carburant Entretien MantenimientoFiltre a AIR Filtro DE Aire Spark Plug Replacement Plug is a NGK CMR7HMA4 Tightening Torque PARE-ETINCELLES Couple DE SerrageSilencieux LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7H Intake AIR Cooling Vent MA6Gear Case MA6 MA7 Boitier DE Renvoi D’ANGLE MA6 Caja DE Engranajes MA6 Cilindro Toma de aire de refrigeración posterior Disposal Procedures to be Performed After Every 100 Hours of USEStorage MA8 Mise au rebut Eliminación Entretien MantenimientoRangement Almacenamiento 26~43.5 in-lbs 2.94~4.9 N.m Guard T3246-24110 Optional blade usageOPT1 OPT2 Bracket Handle 26 43,5 pulg.-lbs Utilisation de la lame optionnelle Uso de hoja opcionalPAR Torsor 94 4,9 N.m Choose the Blade SET UP the BladeOPT3 OPT4 OPT5 Mise EN Place DE LA Lame Monte LA Hoja Choisir LA LameElija LA Hoja Standard Operation OPT6 OPT7 OPT8 OPT9Cutting Method Método DE Corte Methode DE CoupeFonctionnement USO How you can reduce the chance of blade thrust Controlling Blade ThrustWhat causes blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA Hoja How you can maintain the best control Maintenance BladeOPT10 22, 24-tooth blade Tooth blade Point OPT10 Entretien Lame Comment conserver le meilleur contrôle de la machineCuál es la mejor forma de mantener el control Mantenimiento Hoja Guide de localisation des pannes Troubleshooting guide13. Guía de localización y solución de problemas Brushcutters Nota Drive Unit BCZ2601S/BCZ2601S-CA S/N 60100101 and up Optional Blade & Accessories Engine Unit BCZ2601S/BCZ2601S-CA S/N 60100101 and up Description Part Number Qty Manufacturer’s warranty coverage Owner’s warranty responsibilities Couverture de la garantie constructeur Obligations du propriétaire liées à la garantie Cobertura de la garantía dada por el fabricante Responsabilidades del propietario Limited Warranty Garantie limitée Garantía Limitada BCZ2601SW Emission Control Mesures DE Lutte ContreLES Emissions Control DE Emisiones