CPI/LPI Select | Printronix PSA3, P7000 H-Series specification

Chapter 2 The Configuration Menu

Page Format

(from the

previous page)

Form Length

Abs. Length IN 11.0* inches (0.1-24)

Abs. Length MM 279.4* mm (0.1-609.6) Funct. of Lines

66* lines (1-192)

Form Width

Abs. Width IN 13.6* inches (0.1-13.6)

Abs. Width MM 345.4* millimeters (0.1-345.4)

Funct. of CPI 163* Characters (1-272)

Margins

Left Margin 0* columns (0-369)

Right Margin 0* columns (0-369)

Bottom Margin 0* lines (0-451)

Perforation

Skip

Disable* 1/2 inch 2/3 inch 5/6 inch 1 inch

CPI/LPI Select

This parameter lets you specify the characters per inch (cpi) and lines per inch (lpi) values. The defaults are:

•Select CPI - 10.0 cpi

•Select LPI - 6.0 lpi

•DBCS CPI - 6.0 cpi

Host Command

•Enable. The default. Enables all host printing commands.

•Ignore All. This function treats all control codes and printing commands as the data.

•Ignore CPI. This function ignores the CPI selection commands only (e.g., ESC M, ESC P, and ESC G).

•Ignore LPI. This function ignores the LPI selection commands only (e.g., ESC 2 and ESC 0).

•Ignore Unidir. All unidirectional commands sent by the host are ignored by the printer.

•Ignore Pg. Fmt. This function ignores all page format setting commands sent from the host.

22

Image 22

Printronix PSA3, P7000 H-Series manual CPI/LPI Select

Contents

Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table About This Manual Software FeaturesRelated Product Information Software Features Introduction Control Panel Printing The Configuration Printing The Configuration Printing Configurations Step Key Result Allows you to make configuration changes Locks the Enter key Configuration Menu Configuration Menu Overview Configuration Menu Moving Within The Configuration MenuChanging Configurations Step Key Result To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus Menu CPI/LPI Select Font Attributes Margins Form LengthForm Width Perforation Skip Kssm Emulation Kssm Emulation Define CR Code Kssm Emulation Exceptions And Differences Default Values And States Factory Settings Characteristic Default Setting Escape Sequences FS Sequences Set And Reset Codes Configuring The Kssm Emulation With Control CodesSuper-Set Commands Format For Control Code Descriptions Control Code Index Setting the Page FormatSetting the Units Control Code Index Control-code Character Printing Selecting CharactersMechanical Control Printing Graphics Hangul Extension CommandsData and Memory Control Advance Print Position Vertically Align Sbcs Character with Dbcs Character Backspace Cancel The Alignment of Sbcs Character With Dbcs CharacterCancel The Alignment of Sbcs Character With Ascii Code Hex Code Dec Code Purpose Barcode Printing Ascii Hex Selects Barcode Offset unit Barcode Printing Ascii Selects ValueInch UPC-A UPC-E EAN Carriage Return Cancel LineBeeper Beeper Define Pattern for Special Printing Effect Define User-Defined Character Define User-Defined Chinese Character Define User-Defined Chinese CharacterDelete Last Character in Buffer Hex Code Dec Code Enable Printing of Upper Control Codes Divided Hangul Double Height Enable Upper Control Codes Enable Upper Control CodesFont Expansion Form Feed Graphic Printing Initialize Printer Graphics Printing Select Bit ImageGraphics Printing Select Bit Image Line Feed Ascii Code ESC ! n Hex Code Master SelectMaster Select Bit On/Off Hex Dec Function Equivalent Master Select In Dbcs Mode Ascii Code FS ! n Hex Code Pair Two Characters in Vertical Printing Master Select One-Line Attribute In Dbcs ModeMaster Select One-Line Attribute In Dbcs Mode Bit On/Off Hex Dec Function Select 1/6-inch Line Spacing Reassign Bit-image ModeSelect 1/8-inch Line Spacing Select 15 CPI Select 10 CPISelect 12 CPI Select 10 CPI Select 60-dpi Graphics Select 120-dpi Graphics Select 240-dpi Graphics Select 120-dpi Graphics Select an International Character Set USA Select Bit Image Select Bit Image Select Bold Font Cancel Bold FontSelect Character Style Select Character Table Select Character TableSelect Condensed Printing Ascii Code ESC t n Hex Code Cancel Condensed Printing Select Double-strike Printing Cancel Double-strike PrintingSelect Dbcs Print Quality Select Dbcs Print Quality Cancel Double-width Printing One Line Select Double-width Printing One Line Cancel Double-width Printing in Dbcs Mode One Line Select Double-width Printing in Dbcs Mode One LineSelect Double-width Printing in Dbcs Mode One Select Hangul Myunjo/Gothic Style Select Dbcs ModeCancel Dbcs Mode Ascii Code Hex Code Select Print Quality Cancel Italic FontSelect Italic Font Select Italic Font Deselect Printer Select PrinterSelect Superscript/Subscript Printing Select Dbcs Super/Subscript Printing Cancel Superscript/Subscript PrintingCancel Superscript/Subscript Printing Select Vertical Printing Set n/60-inch Line Spacing Cancel Vertical Printing Select Horizontal PrintingSet n/180-inch Line Spacing Set Bottom Margin Cancel Bottom MarginSet Absolute Horizontal Print Position Set Absolute Horizontal Print Position Set Horizontal Tabs Cancel Dbcs Character Half Width Super/Subscript PrintingSet Dbcs Character Half Width Ascii Code ESC D n1 n2 … nk NUL Set Intercharacter Space Set Intercharacter Space Set Left Margin Set Page Length In Lines Set Page Length In InchesSet Page Length In Inches Set Relative Horizontal Print Position Set Right Margin Set Vertical Tab Channels Set Vertical Tab ChannelsSet Vertical Tabs Ascii Code ESC B n1 n2 … nk NUL Ascii Code ESC b m n1 … nk NUL Set Vertical Tabs In VFU ChannelsDec Code 27 98 m n1 … nk Tab Vertically Tab HorizontallyTab Horizontally Turn Auto-wrap Around On/Off Turn Double-Height Printing On/Off Turn Double-Width Printing On/Off Turn Double-Width, Double-Height Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn On/Off Ocrb Selection Turn Extending Table Character On/OffAscii Code Assc 0 z n Turn Proportional Mode On/Off Turn Proportional Mode On/OffTurn Underline On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Customer Support Center Printronix Supplies Department Corporate Offices Appendix C Contact Information Index Page Page 100 Page 179981-001