Highlight Protocol and then click Add | Siemens CL-010-I specification

Image 22

Siemens CL-010-I manual Highlight Protocol and then click Add, Click Internet Protocol TCP/IP and then click OK

Contents

CL-010/CL-010-I ADSL2+ Router User’s ManualThis manual currently suits for CL-010/CL-010-I Safety Notes For Installation For Using For Service ICES-003 Class B Notice - Avis NMB-003, Classe B FCC FCC Class B NoticeIC Statement ADSL Router User Manual ATM Features FeaturesPreface ADSL Compliance Security Features Bridging FeaturesRouting Features Configuration and Management Unpacking Subscription for ADSL Service Page LED Indicators Chapter 1 OverviewPhysical Outlook Front Panel 9VAC Rear Panel9 VAC Ethernet Choosing a place for the ADSL Router Chapter 2 System Requirement and InstallationSystem Requirement ™ ™ ™ ™ Connecting the ADSL Router Setting TCP/IP Chapter 3 Configuration For Windows 7. On IP Address tab 8. When returning to Network window, click OK 9. Wait for Windows copying files For Windows ME For Windows NT 5. Click Yes to use DHCP 9. When returning to Network window, click Close Option 2 If you have TCP/IP Protocol, go to Step 4. Highlight Protocol and then click Add 5. Click Internet Protocol TCP/IP and then click OK Properties For Windows XPPanel and then click Network and Internet Connections Click Internet ProtocolTCP/IP and then click OK For Windows Vista 9. Click Network and Internet 10. Select Network and Sharing Center 12. Right click Local Area Connection and select Properties 11. Click Manage Network Connection on the left sideSelect Internet Protocol Version 4 TCP/IPv4 and press Properties Configure PC to get IP address from DHCP Chapter 3 Configuration When prompted with the message below, click Yes to continue Enable Obtain an IP address automatically and then click OK Windows Vista Renew IP Address on Client PC For Windows 98ME 2. Select Run from the Start menu 3. Type cmd in the dialog box and the click OK 1. From the Start menu, point to Programs, Accessories and then click Command Prompt For Windows Vista Page Chapter 3 Connecting and Accessing Internet Chapter 3Connecting and Accessing Internet PPP over ATM PPP over ATM PPPoA ModeConfiguration Description 2. Go to Advanced - Internet - Connections. And click Add PPP over ATM PPPoA IP Extension ModePrimary IP address192.168.1.1 Subnet Mask255.255.255.0 PPP over Ethernet PPPoE Mode PPP over Ethernet PPP over Ethernet PPPoE IP Extension Mode Secondary DNS server Numbered IP over ATM IPoAWAN IP Address WAN Subnet Mask Primary DNS server Primary IP Address Subnet mask Start IP Address End IP Address IP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT Primary IP Address Subnet mask Start IP Address End IP Address Unnumbered IP over ATM IPoA Primary DNS server Secondary DNS server Chapter 3Accessing Internet Unnumbered IP over ATM IPoA+NAT Primary IP Address Subnet mask Start IP Address End IP Address Bridge Mode Chapter 4 Web Configuration Using Web-Based Manager Language To Have the New Settings Take EffectOutline of Web Manager Title Connect to Internet Quick StartQuick Setup Connection TypePage PPP over ATM/ PPP over Ethernet Always On PPP PasswordPPP Username Dial on Demand Leased Time Start IP AddressEnd IP Address DHCP Server Off WAN IP Address IP over ATMNone WAN Subnet Mask Secondary IP Address Primary IP AddressSubnet Mask Subnet Mask Please wait for 2 minutes for restarting the router Bridging DHCP Server On Status Overview ADSL Line ADSL BER Test DHCP Table Internet ConnectionTraffic Statistics Routing TablePage Local Network - DHCP Server Advanced SetupLocal Network- IP Address Host Name Relay On Server and Relay Off Chapter 5Connection Mode Local Network - UPnP Internet-Connections SettingService Category Adding a New One Chapter 5Connection Mode Internet-IGMP Proxy IGMP Proxy EnabledInternet-DNS Server Internet Connection Capability Enabled Internet - ADSL SettingsEnable ADSL Port IP Routing - Static Route Remove Static Route Configuring Other Routers on Your LANGateway IP Address Local Router Example - Static Route EnabledIP Routing - Dynamic Routing For the Router’s Routing Table different interface. Otherwise, disable this function Click Apply to invoke the settings set here Virtual Server-Port Forwarding Pre-defined IP Address seen by Internet UsersAdd New Port Forwarding User defined Virtual Server-Port Triggering Connecting to the Virtual ServersFrom Internet Host IP Address Virtual Server - DMZ Host Dynamic DNS： Password：Virtual Server - Dynamic DNS Internet Connection： Filtering by IP address FirewallSelect the direction to filter packets Source/Destination IP address Allow TrafficProtocol Port Range Traffic Class Name Quality of ServiceBridge QoS 802.1p Priority Source IP Address/ Subnet Mask IP type of ServiceIPQoS Source Port Port Mapping Destination Port Group Name Available Interfaces Management Diagnostics Select the Internet Connection Admin AccountRemote Access Web Browser Interntet Time UpdateConfigure System Log System Log Viewing System Log View System Log button SNMP Agent SNMP SettingEnable TRAP Service Read Community Update Firmware Backup ConfigReset Router UPnP for XP http//192.168.1.1/index.html Chapter 5Connection Mode Problems with LAN Chapter 5 TroubleshootingProblems with WAN Problems with Upgrading DHCP Dynamic Host Configuration Protocol Chapter 6 GlossaryARP Address Resolution Protocol LAN Local Area Network & WAN Wide Area Network PVC Permanent Virtual Circuit Private IP AddressPublic IP Address RIP Routing Information ProtocolPage Chapter 7 Glossary Appendix A Specifications Appendix A Specifications Getting Client Certificate Appendix B Server Setup for 802.1x Client4. Make sure that Request a certificate is selected, and click Next Appendix C WEEE - B2C Appendix C WEEE - B2C