Internet - ADSL Settings, Enable ADSL Port, Delete | Siemens CL-010

Image 71

Siemens CL-010 Internet - ADSL Settings, IP Routing - Static Route, Enable ADSL Port, Capability Enabled, Bitswap, Netmask

Contents

This manual currently suits for CL-010/CL-010-I User’s ManualCL-010/CL-010-I ADSL2+ Router For Installation For Using For Service Safety Notes ADSL Router User Manual FCC FCC Class B NoticeIC Statement ICES-003 Class B Notice - Avis NMB-003, Classe B ADSL Compliance FeaturesPreface ATM Features Configuration and Management Bridging FeaturesRouting Features Security Features Unpacking Subscription for ADSL Service Page Front Panel Chapter 1 OverviewPhysical Outlook LED Indicators Ethernet Rear Panel9 VAC 9VAC ™ ™ ™ ™ Chapter 2 System Requirement and InstallationSystem Requirement Choosing a place for the ADSL Router Connecting the ADSL Router Chapter 3 Configuration Setting TCP/IP For Windows 7. On IP Address tab 9. Wait for Windows copying files 8. When returning to Network window, click OK For Windows ME For Windows NT 5. Click Yes to use DHCP 9. When returning to Network window, click Close Option 2 If you have TCP/IP Protocol, go to Step 5. Click Internet Protocol TCP/IP and then click OK 4. Highlight Protocol and then click Add Click Internet ProtocolTCP/IP and then click OK For Windows XPPanel and then click Network and Internet Connections Properties 9. Click Network and Internet 10. Select Network and Sharing Center For Windows Vista Select Internet Protocol Version 4 TCP/IPv4 and press Properties 11. Click Manage Network Connection on the left side12. Right click Local Area Connection and select Properties Configure PC to get IP address from DHCP For Windows ME Enable Obtain an IP address automatically and then click OK When prompted with the message below, click Yes to continue Windows Vista For Windows 98ME Renew IP Address on Client PC 3. Type cmd in the dialog box and the click OK 2. Select Run from the Start menu 1. From the Start menu, point to Programs, Accessories and then click Command Prompt For Windows Vista Page Chapter 3Connecting and Accessing Internet Chapter 3 Connecting and Accessing Internet Description PPP over ATM PPPoA ModeConfiguration PPP over ATM Primary IP address192.168.1.1 Subnet Mask255.255.255.0 PPP over ATM PPPoA IP Extension Mode2. Go to Advanced - Internet - Connections. And click Add PPP over Ethernet PPP over Ethernet PPPoE Mode PPP over Ethernet PPPoE IP Extension Mode Primary IP Address Subnet mask Start IP Address End IP Address Numbered IP over ATM IPoAWAN IP Address WAN Subnet Mask Primary DNS server Secondary DNS server IP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT Secondary IP Address Subnet mask Primary DNS server Secondary DNS server Unnumbered IP over ATM IPoA IP Address Subnet Mask Gateway Primary IP Address Subnet mask Unnumbered IP over ATM IPoA+NAT Start IP Address End IP Address Bridge Mode Using Web-Based Manager Chapter 4 Web Configuration Title To Have the New Settings Take EffectOutline of Web Manager Language Connection Type Quick StartQuick Setup Connect to InternetPage PPP over ATM/ PPP over Ethernet Dial on Demand PPP PasswordPPP Username Always On DHCP Server Off Start IP AddressEnd IP Address Leased Time WAN Subnet Mask IP over ATMNone WAN IP Address Subnet Mask Primary IP AddressSubnet Mask Secondary IP Address Please wait for 2 minutes for restarting the router Bridging Start IP Address Overview Status ADSL BER Test ADSL Line Routing Table Internet ConnectionTraffic Statistics DHCP TablePage Host Name Advanced SetupLocal Network- IP Address Local Network - DHCP Server Server and Relay Off Relay On Chapter 5Connection Mode Adding a New One Internet-Connections SettingService Category Local Network - UPnP Chapter 5Connection Mode Internet Connection IGMP Proxy EnabledInternet-DNS Server Internet-IGMP Proxy IP Routing - Static Route Internet - ADSL SettingsEnable ADSL Port Capability Enabled Local Router Configuring Other Routers on Your LANGateway IP Address Remove Static Route For the Router’s Routing Table EnabledIP Routing - Dynamic Routing Example - Static Route Click Apply to invoke the settings set here different interface. Otherwise, disable this function Virtual Server-Port Forwarding User defined IP Address seen by Internet UsersAdd New Port Forwarding Pre-defined From Internet Host IP Address Connecting to the Virtual ServersVirtual Server-Port Triggering Virtual Server - DMZ Host Internet Connection： Password：Virtual Server - Dynamic DNS Dynamic DNS： Select the direction to filter packets FirewallFiltering by IP address Port Range Allow TrafficProtocol Source/Destination IP address 802.1p Priority Quality of ServiceBridge QoS Traffic Class Name Source Port IP type of ServiceIPQoS Source IP Address/ Subnet Mask Destination Port Port Mapping Available Interfaces Group Name Diagnostics Management Web Browser Admin AccountRemote Access Select the Internet Connection System Log UpdateConfigure System Log Interntet Time View System Log button Viewing System Log Read Community SNMP SettingEnable TRAP Service SNMP Agent Reset Router Backup ConfigUpdate Firmware http//192.168.1.1/index.html UPnP for XP Chapter 5Connection Mode Problems with WAN Chapter 5 TroubleshootingProblems with LAN Problems with Upgrading LAN Local Area Network & WAN Wide Area Network Chapter 6 GlossaryARP Address Resolution Protocol DHCP Dynamic Host Configuration Protocol RIP Routing Information Protocol Private IP AddressPublic IP Address PVC Permanent Virtual CircuitPage Chapter 7 Glossary Appendix A Specifications Appendix A Specifications 4. Make sure that Request a certificate is selected, and click Next Appendix B Server Setup for 802.1x ClientGetting Client Certificate Appendix C WEEE - B2C Appendix C WEEE - B2C