Star Micronics LC24-20 user manual Bail Lever Functions

I

BAIL LEVER FUNCTIONS

The ba!l lever ISused to control paper.

Ifthepaper,s .otmo.nted on the prlnler, usetheball Ie.ertoload the paper. When you open the bail lever with the fanfold paper I. On-line. the Printer goes off-llne md the ball lever a.tomat,cally closed, then the pmter also feeds the paper forward. Thts allows you to cur II offpst below the last Ihne printed

When you open the bail lever q.,., the paper feeds backward Nopp,ng whew y.. left oft, md the pr,nter returns to on-line.

EDS MODE

Fmmthecontrol panel you... change the parameters lhatdef$ne h.wyo. r

pri.terworks. This funct(on ,scalledthe Electro”(c DIP Sw,t.h (EDS) mode.

The EDS mode has f6 funct,ons you can set. $ the power-on default.

T.rnthepr,"teron while simultaneously holdlngthe F0NT ,PITCHand EJECTl PARK buttons

The EDS’, message WII1show on the d,splay, and enter the EDS mode.

In EDS mode, the butlons on the control panel are used as shown below

. Use lhe FONT b.tton to select the Bank Letter.

. Use lhe PITCH button to select the Swdch Number

. The LCD display on the control panel shows the c.rrentsettlng.

Use the EJECTIPARK button to change the setbngs.

. Press the PAPER FEED button m pr(nt the current senlngs

. Press the ON LINE button loex(t the EDS mode

Number		F“ncti.n	ON	OFF
A.?	Ern.lat,on		STANOARD’EPSON	IBM
AZ	AEC Mode		Enabled	D#sabled
A.3	RAM Usage		1nP”, B.f:er	D.wnload8uf1er
A-4	Auk	LFw,lh CR	D,sebled	Enabled
A.5	Auk	Sheet Feeder	Notrnstalled	Installed
A.6	GmPh,cs O#rectro”		B1-d$rect)mal	Un,-dwect,.mal

0.1(No, used]

8.2 P.perm., Enablea I D,mbled

0.3(Not used]

8.4	[Reserved)	Leave ON
0.5	Pr,ntable Ar&3	TyPe A	I TyPe B

8.6(No1 used)

c-?		~r,n, ~tie	(see table 1)
C-2
C.3
C-4		Page Length	(See (able21
“.	(		1
b.

0.1Char.c,er Table

		ISlmdard model	m:t;,cs	,,,,,.,
		(IBM mode)		set *I
~	D-2	I 10MCode PaQeor	I
		Intemamnal	I(Seetable3 and4)

H+-
;.;	LO Font Selec!,on	(Seelable	51
E-4
E.5
F.,	EDS Sen<ng	current	I m,.,

Table 1

Pr, ntM.ade	C-1	C-2
IOCPI DRAFT	ok	ON
,OCPI HS ORAFT	ON	OFF
,7 CPl DRAFl	OFF	ON
a ,OCPI ,(3	OFF	OFF

			,,
Table	3
IBM C.ade Page			D-2 D-3
.“.,	,,.	A	m.,	ON
				,N
				IFF
				)FF
lame	4
Country		D-2	D-3	0-4
uSA		[ ON	I ON	I ON
France		I OFF	I ON	[ ON
I IGerm.inON.			i OFF	I
Table	5
.,,	.,.”,.,”	-	. . . .
Rome,”		ON	ON	Oh
S.	”,,,(I	OFF	ON	Oh
co.,,.,		ON	OFF	Oh
P,,.!(w		OFF	OFF	Oh
B		A.,	n.,	n.

	.. . .
	T..,.	,
D-4	EaIBM Code PageD-2 D-3 D-4
	Page Length			C-3 C-4 C-5
	11	,“ches, Letter		ON	ON	ON
	8,n.hes			OFF	ON	ON
	11	7,n.hes,	A4	ON	OFF	ON
	12	,nch.s		OFF	OFF	ON
	851nches, Le,,er			ON	ON	OFF
	,4, ”c,WL,		al	OFF	ON	OFF
	,05,.ches,		Execuwe	ON	OFF	OFF
	725 ,nches, Exec”t,”e			OFF	OFF	OFF

~~#863 Cmad,an French ON ON OFF

ON	#865 Nord,c	OFF	ON	OFF
ON	,Reser”ed]	ON	OFF	OFF
ON	,Reswved]	OFF	OFF	OFF

Country D-2 D-3 D-4

Denmark 1 ON ON OFF

Sweden OFF ON OFF

ON OFF OFF

spa,. !OFF OFF OFF

NOTE :The factory default K the ON” position for .11 funct$ons

exce Dt A-6 which ISset to the OFF post,.. w