Copyright & Trademarks | TP-Link TD-8816 specification

Image 2

TP-Link TD-8816 manual Copyright & Trademarks

Contents

TD-8816 ADSL2+ Modem Router Rev3.1.0 1910010870 COPYRIGHT & TRADEMARKS FCC STATEMENT CE Mark Warning Safety Information EN 60950-12006+A11：2009+A12010+A122011 DECLARATION OF CONFORMITYEN EN EN 61000-3-22006+A12009+A22009 EN The product carries the CE Mark Hardware Installation CONTENTSPackage Contents Chapter 3. Quick Installation Guide Appendix C Troubleshooting AppendixA SpecificationsAppendix B Configuring the PC Appendix D Technical Support ADSL2+ Modem Router User Guide Package ContentsTD-8816  Note 1.1 Product Overview 1.2 Main FeaturesChapter 1. Introduction ADSL 1.3 Conventions LED Explanation Chapter 2. Hardware Installation2.1 The Front Panel Name 2.3 Installation Environment 2.2 The Back Panel 2.4 Connecting the Router Step 4 Turn on the TD-8816 and power on the computers and LAN devices Chapter 3. Quick Installation Guide 3.1 TCP/IP Configuration 1 Is the connection between your PC and the modem router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? 192.168.1.1 Click the NEXT button Step 5 Click NEXT to finish the Quick Start 4.1.1 Device Info Chapter 4. Software Configuration4.1 Status 4.1.2 System Log 4.1.3 Statistics  Select ADSL, and you will see the statistics table as below  Select Ethernet, and you will see the statistics table as belowStatistics Table 4.3.1 Internet 4.3 Interface Setup4.2 Quick Start ∙ Virtual Circuit Select the VC number you want to setup, PVC0~PVC7 1. Dynamic IP Address ∙ VCI Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 1 to 31 is reserved for well-known protocols. Please input the value provided by your ISP4.3.1.1. IPv4  TCP MTU Option Enter the TCP MTU as your desire. The default value is 2. Static IP Address  Note 3. PPPoA/PPPoE TD-8816 4. Bridge Mode 4.3.1.2. IPv6 2. Static IP Address Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP octets separated by a colon xxxxxxxx. The modem router will not accept the IP address if it is not in this format TD-8816 4.3.2 LAN 4.3.1.3. IPv4/IPv6  Router Local IP These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet ∙ IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect 4.4.2 Routing 4.4 Advanced Setup4.4.1 Firewall 4.4.3 NAT 4.4.3.1. DMZ 4.4.3.2. Virtual Server Other configurations for the entries as shown in Figure To add a virtual server entry Click the BACK button to return to the previous screen 4.4.3.3. IP Address Mapping 4.4.4 QoS To add a mapping rule  QoS Select this option to Activate/Deactivate the QoS TD-8816 4.4.5 VLAN 5. Define VLAN Group  VLAN ID This indicates the VLAN group 6. Assign VLAN PVID for each Interface 4.5.1 ACL 4.5 Access Management4.4.6 ADSL 4.5.2 Filter 4.5.2.1. IP Filter  Interface Select the interface for the entry  Rule Type For IP Filter, please select IP here To add an IP Address filtering entry 4.5.2.2. MAC Filter To add a MAC Address filtering entry 4.5.2.3. Application Filter  Application Filter Activate or deactivate the function 4.5.2.4. URL Filter 4.5.3 SNMP To add a URL filter entry 4.5.4 UPnP 4.5.5 DDNS 4.5.6 CWMP 4.6 Maintenance 4.6.1 Administration 4.6.2 Time Zone 1. NTP Server automatically 3. Manually 4.6.3 Firmware2. PC’s Clock 4 The modem router will reboot after the upgrading has been finished To back up the Router’s current settings 4.6.4 SysRestart To restore the modem router’s settings 4.6.5 Diagnostics 4.7 Help  Note Physical and Environment AppendixA SpecificationsGeneral Figure B-1 Appendix B Configuring the PC1. Configure TCP/IP component Figure B-2 Now you have two ways to configure the TCP/IP protocol below Setting IP address automatically shown in the Figure below  Setting IP address manually Figure B-3 Click OK to keep your settings Figure B-4 Now For Mac OS Appendix C TroubleshootingT2. What can I do if I don’t know or forgot my password? b Go to “System Preferences - Network” b Click “View network status and tasks Change adapter settings” Click Internet Options Select Never dial a connection T4. What can I do if I cannot access the Internet?  Note Appendix D Technical Support Technical Support