Introduction, Product Overview, Main Features | TP-Link TD-8816

Image 9

TP-Link TD-8816 manual Introduction, Product Overview, Main Features, Adsl, ADSL2+ Modem Router User Guide

Contents

Rev3.1.0 1910010870 TD-8816 ADSL2+ Modem Router COPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENT Safety Information EN EN EN 61000-3-22006+A12009+A22009 EN DECLARATION OF CONFORMITYEN 60950-12006+A11：2009+A12010+A122011 The product carries the CE Mark Package Contents CONTENTSHardware Installation Chapter 3. Quick Installation Guide Appendix B Configuring the PC AppendixA SpecificationsAppendix C Troubleshooting Appendix D Technical Support TD-8816 Package ContentsADSL2+ Modem Router User Guide  Note Chapter 1. Introduction 1.2 Main Features1.1 Product Overview ADSL 1.3 Conventions 2.1 The Front Panel Chapter 2. Hardware InstallationLED Explanation Name 2.2 The Back Panel 2.3 Installation Environment 2.4 Connecting the Router Step 4 Turn on the TD-8816 and power on the computers and LAN devices 3.1 TCP/IP Configuration Chapter 3. Quick Installation Guide 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the modem router correct? 192.168.1.1 Click the NEXT button Step 5 Click NEXT to finish the Quick Start Chapter 4. Software Configuration 4.1 Status4.1.1 Device Info 4.1.2 System Log 4.1.3 Statistics  Select Ethernet, and you will see the statistics table as below Statistics Table Select ADSL, and you will see the statistics table as below 4.3 Interface Setup 4.2 Quick Start4.3.1 Internet ∙ Virtual Circuit Select the VC number you want to setup, PVC0~PVC7 ∙ VCI Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 1 to 31 is reserved for well-known protocols. Please input the value provided by your ISP 4.3.1.1. IPv41. Dynamic IP Address 2. Static IP Address  TCP MTU Option Enter the TCP MTU as your desire. The default value is 3. PPPoA/PPPoE  Note ADSL2+ Modem Router User Guide 4.3.1.2. IPv6 4. Bridge Mode TD-8816 Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP octets separated by a colon xxxxxxxx. The modem router will not accept the IP address if it is not in this format ADSL2+ Modem Router User Guide 4.3.1.3. IPv4/IPv6 4.3.2 LAN  Router Local IP These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet ∙ IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.2. Virtual Server 4.4.3.1. DMZ To add a virtual server entry Other configurations for the entries as shown in Figure 4.4.3.3. IP Address Mapping Click the BACK button to return to the previous screen To add a mapping rule 4.4.4 QoS  QoS Select this option to Activate/Deactivate the QoS ADSL2+ Modem Router User Guide 5. Define VLAN Group 4.4.5 VLAN 6. Assign VLAN PVID for each Interface  VLAN ID This indicates the VLAN group 4.5 Access Management 4.4.6 ADSL4.5.1 ACL 4.5.2.1. IP Filter 4.5.2 Filter  Interface Select the interface for the entry To add an IP Address filtering entry  Rule Type For IP Filter, please select IP here 4.5.2.2. MAC Filter To add a MAC Address filtering entry 4.5.2.3. Application Filter 4.5.2.4. URL Filter  Application Filter Activate or deactivate the function To add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP 4.5.6 CWMP 4.5.5 DDNS 4.6.1 Administration 4.6 Maintenance 1. NTP Server automatically 4.6.2 Time Zone 4.6.3 Firmware 2. PC’s Clock3. Manually To back up the Router’s current settings 4 The modem router will reboot after the upgrading has been finished To restore the modem router’s settings 4.6.4 SysRestart 4.7 Help 4.6.5 Diagnostics TD-8816 AppendixA Specifications GeneralPhysical and Environment Appendix B Configuring the PC 1. Configure TCP/IP componentFigure B-1  Setting IP address automatically Now you have two ways to configure the TCP/IP protocol belowFigure B-2 shown in the Figure below Figure B-3  Setting IP address manually Figure B-4 Now Click OK to keep your settings T2. What can I do if I don’t know or forgot my password? Appendix C TroubleshootingFor Mac OS b Go to “System Preferences - Network” Click Internet Options Select Never dial a connection b Click “View network status and tasks Change adapter settings”  Note T4. What can I do if I cannot access the Internet? Appendix D Technical Support Technical Support