Husqvarna YTH2242 To USE Cruise Control J See Fig, To Adjust Mower Cutting Height See Fig

Page 10

OPERATION

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

K

J

L

Fig. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 " during the cool season and to over 3"during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES

•Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield

(S) in place (See Fig. 10).

S

Fig. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH2242 General Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceGeneral Service IV. TowingTable of Contents Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerReverse Operation System ROS Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningMuffler Deck Washout Port See FigTo Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Remove Wheel See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Engine OIL OtherFuel System CylindersTroubleshooting Problem Cause CorrectionEngine continues Schematic Tractor - Model Number YTH2242 96043010000, Product no 43Electrical KEY Part Description Chassis Tractor - Model Number YTH2242 96043010000, Product no 43 Drive 532 42 61-20Transaxle, Tufftorq K46BT Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH2242 96043010000, Product no 43 Mower Deck KEY Part NO. no Description Mower Lift 100 101Seat Assembly 532 42 SeatDecals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 10.23.09 CL
Related manuals
Manual 48 pages 54.49 Kb

YTH2242 specifications

The Husqvarna YTH2242 is a versatile and robust garden tractor designed for homeowners seeking a reliable and efficient mowing solution. This model features a powerful 22 horsepower Kohler engine that provides ample power for cutting through tough grass and uneven terrain. The engine is engineered for durability and performance, ensuring that it can handle a variety of yard conditions with ease while delivering smooth starts and strong acceleration.

One of the standout features of the YTH2242 is its 42-inch cutting deck, which allows for a wider cutting path, making it ideal for mid-sized lawns. The cutting height can be easily adjusted with a lever located on the dashboard, offering six different height positions to achieve the perfect grass length. This feature is particularly beneficial for homeowners who prefer maintaining a manicured lawn or adjusting cut height for seasonal changes.

The YTH2242 is equipped with a hydrostatic transmission, allowing for smooth, variable speed control without the need for manual gear shifting. This transmission technology enables effortless navigation around obstacles and provides increased maneuverability, especially in tight spaces. Additionally, the model has tight turning capabilities, making it effective for trimming around trees and flower beds.

Ergonomy is a key consideration in the design of the YTH2242. The comfortable seat is adjustable, allowing drivers of different sizes to find their ideal driving position effortlessly. The user-friendly dashboard is equipped with easy-to-read gauges and controls, enhancing the overall experience. The steering wheel is designed for precise control, minimizing fatigue during longer mowing sessions.

For added convenience, the YTH2242 features a connector for optional attachments, such as bags, mulchers, and snow removal equipment, promoting year-round usability. The tight-knit construction and quality materials ensure longevity, and the cutting deck’s washout port simplifies maintenance by allowing users to clean the underside easily, preventing grass buildup.

In summary, the Husqvarna YTH2242 combines power, flexibility, and comfort in a compact design, making it a valuable addition to any homeowner's gardening arsenal. With its reliable engine, adjustable cutting deck, user-friendly features, and adaptability, it stands out as a top choice for those looking to maintain a pristine lawn with ease.
Top Page Image Contents