Husqvarna YTH2242 To Remove Wheel See Fig, Front Wheel TOE-IN/CAMBER, Replacing Battery See Fig

Page 22

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL (See Fig. 32)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 32

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO START ENGINE WITH A WEAK BATTERY (See Fig. 33)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR

FULLY CHARGED

DEAD BATTERY

BATTERY

Fig. 33

REPLACING BATTERY (See Fig. 34)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining bolt and nut. Tighten securely.

•Lower seat pan.

SEAT PAN

 

TERMINAL

NUT

COVER

BOLT

 

POSITIVE

NEGATIVE

(RED)

(BLACK)

CABLE

CABLE

02603

 

Fig. 34

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH2242 General Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceGeneral Service IV. TowingTable of Contents Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerReverse Operation System ROS Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningMuffler Deck Washout Port See FigTo Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Remove Wheel See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Engine OIL OtherFuel System CylindersTroubleshooting Problem Cause CorrectionEngine continues Schematic Tractor - Model Number YTH2242 96043010000, Product no 43Electrical KEY Part Description Chassis Tractor - Model Number YTH2242 96043010000, Product no 43 Drive 532 42 61-20Transaxle, Tufftorq K46BT Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH2242 96043010000, Product no 43 Mower Deck KEY Part NO. no Description Mower Lift 100 101Seat Assembly 532 42 SeatDecals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 10.23.09 CL
Related manuals
Manual 48 pages 54.49 Kb

YTH2242 specifications

The Husqvarna YTH2242 is a versatile and robust garden tractor designed for homeowners seeking a reliable and efficient mowing solution. This model features a powerful 22 horsepower Kohler engine that provides ample power for cutting through tough grass and uneven terrain. The engine is engineered for durability and performance, ensuring that it can handle a variety of yard conditions with ease while delivering smooth starts and strong acceleration.

One of the standout features of the YTH2242 is its 42-inch cutting deck, which allows for a wider cutting path, making it ideal for mid-sized lawns. The cutting height can be easily adjusted with a lever located on the dashboard, offering six different height positions to achieve the perfect grass length. This feature is particularly beneficial for homeowners who prefer maintaining a manicured lawn or adjusting cut height for seasonal changes.

The YTH2242 is equipped with a hydrostatic transmission, allowing for smooth, variable speed control without the need for manual gear shifting. This transmission technology enables effortless navigation around obstacles and provides increased maneuverability, especially in tight spaces. Additionally, the model has tight turning capabilities, making it effective for trimming around trees and flower beds.

Ergonomy is a key consideration in the design of the YTH2242. The comfortable seat is adjustable, allowing drivers of different sizes to find their ideal driving position effortlessly. The user-friendly dashboard is equipped with easy-to-read gauges and controls, enhancing the overall experience. The steering wheel is designed for precise control, minimizing fatigue during longer mowing sessions.

For added convenience, the YTH2242 features a connector for optional attachments, such as bags, mulchers, and snow removal equipment, promoting year-round usability. The tight-knit construction and quality materials ensure longevity, and the cutting deck’s washout port simplifies maintenance by allowing users to clean the underside easily, preventing grass buildup.

In summary, the Husqvarna YTH2242 combines power, flexibility, and comfort in a compact design, making it a valuable addition to any homeowner's gardening arsenal. With its reliable engine, adjustable cutting deck, user-friendly features, and adaptability, it stands out as a top choice for those looking to maintain a pristine lawn with ease.
Top Page Image Contents