Husqvarna YTH2248 owner manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 20

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 18)

•Place attachment clutch in “DISENGAGED” position.

•If equipped, turn height adjustment knob to lowest setting.

•Lower mower to its lowest position.

•Remove retainer spring holding anti-swaybar to chassis bracket and disengage anti-swaybar from bracket.

•Remove four retainer springs from front plate assembly and remove plate.

•Remove retainer springs from suspension arms at deck and disengage arms from deck.

•Raise attachment lift to its highest position.

•Slide mower forward and remove belt from electric clutch pulley.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage park- ing brake.

•Swing anti-sway bar to left side of mower deck.

•Slide mower under tractor with deflector shield to right side of tractor.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

CHASSIS

SUSPENSION ARMS

BRACKET

 

•If equipped, turn height adjustment knob counter- clockwise until it stops.

•Lower mower linkage with attachment lift control.

•Install belt into electric clutch pulley groove.

•Place the suspension arms on outward pointing deck pins. Retain with double loop retainer spring with loops up as shown.

•Install front plate assembly to tractor suspension brackets and retain with single loop retainer springs as shown.

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate and mower brack- ets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

 

ELECTRIC CLUTCH PULLEY

FRONT MOWER

FRONT PLATE ASSEMBLY

BRACKET

DOUBLE LOOP

 

 

RETAINER SPRING

 

SINGLE LOOP

 

REATINER

 

SPRING

RETAINER

SPRING

USE PLIERS FOR

RETAINER SPRINGS

LOOP UP

ANTI-SWAY

BAR

SUSPENSION ARMS DOUBLE LOOP RETAINER SPRINGS (Outward pointing deck pins)

FLANGED PINS

02566

FIG. 18

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents YTH2248 Safety Rules IV. ServiceGeneral Operation II. Slope Operation NN Ordere to Prevent Acci Table of Contents Unassembled Parts MowerAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See Figs Check Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Hourmeter Indicates hours of operationHOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Purge TransmissionMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning AIR FilterEngine OIL Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Check and Adjust Brake See Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentTo Start Engine with a Weak BATTERYSee Fig To Remove Wheel for Repairs See FigReplacing Battery See Fig To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves seat Service Notes Schematic Tractor Model NO. YTH2248 YTH2248A, Product no 57Electrical KEY Part NO. NO. Description Chassis and Enclosures Repair Parts Drive KEY Part Description Steering Assembly KEY Part NO. NO. Description Seat Assembly KEY Part NO. no Description NO. NO. DescriptionDecals Wheels & TiresEngine Mower Lift Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Fold Along This Dotted Line DegreeWarranty Statement 532 18 99-07 Rev 6.8.04 RD/MH
Top Page Image Contents