Husqvarna CTH2036 TWIN owner manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 28

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thor- oughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

Lubricate as shown in the Maintenance section of this manual.

Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

Fully charge the battery for storage.

After a period of time in storage, battery may require recharging.

To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

Remove spark plug(s).

Pour one ounce of oil through spark plug hole(s) into cylinder(s).

Turn ignition key to “START” position for a few seconds to distribute oil.

Replace with new spark plug(s).

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your tractor indoors and cover it to give protection from dust and dirt.

Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

28

Image 28
Contents CTH2036 Twin Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See Figs A-5CBagger Adjustment See Horizontal AdjustmentVertical Adjustment To Assemble and Install Mulcher Plug See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation System See FigTo Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills Service REMINDER/HOUR MeterTo Transport See Figs Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsTo Convert Mower See To Dump Bagger SeeBagging See Maintenance Lubrication ChartBlade CARESee Figs.20-22 TractorStar Pattern Blade Engine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Check BrakeTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Adjust Throttle Control Cable To Adjust CarburetorTo Start Engine with a Weak BAT- Tery To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Schematic TRACTOR- -MODEL NO. CTH2036TWIN 96061021701, Product no 61Electrical KEY Part Description Chassis and Enclosures Chassis and Enclosures Drive TRACTOR- -MODEL NO. CTH2036TWIN 96061021701, Product no 61 Steering Assembly 532 19 Steering Wheel Engine 532 18 Control Throttle Seat Assembly 532 18 SeatDecals Wheels & TiresMower Mandrel Asm CRD LH Threads SVC Mower Lift Bagger 532 16 52-49 Tube Handle Bagger CRDService Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation 532 41 55-01 Rev 07.07.08 AP