SERVICE AND ADJUSTMENTS
TO ATTACH JUMPER CABLES -
•Connect one end of the RED cable to the POSITIVE
(+)terminal of each
•Connect one end of the BLACK cable to the NEGATIVE
•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER -
•BLACK cable first from chassis and then from the fully charged battery.
•RED cable last from both batteries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WEAK OR | FULLY CHARGED | |||||||||||||||||||||||||
DEAD BATTERY | BATTERY | |||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. 34
REPLACING BATTERY (See Fig. 35)
WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.
•Open battery cover.
•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.
•Install new battery with terminals in same position as old battery.
•First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal.
•Connect BLACK grounding cable to negative
•Close battery cover.
BATTERY
COVER
POSITIVE
(RED)
CABLE
NUT
BOLT
NEGATIVE (BLACK)
CABLE
Fig. 35
TO REPLACE HEADLIGHT BULB
•Raise hood.
•Pull bulb holder out of the hole in the backside of the grill.
•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
•Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.
•Check wiring. See electrical wiring diagram in the Repair Parts section.
TO REPLACE FUSE
Replace with 20 amp
TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 36)
•Raise hood.
•Unsnap headlight wire connector.
•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.
•To replace, reverse above procedure.
HOOD |
HEADLIGHT WIRE |
CONNECTOR |
03076 |
Fig. 36
TRANSMISSION REMOVAL/REPLACEMENT
Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.
ENGINE
TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.
TO ADJUST CARBURETOR
The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.
27