Husqvarna 232R, 235R, 235FR manual Air filter Spark plug, Angle gear, Two-part shaft

Page 26

MAINTENANCE

Air filter

Spark plug

The air filter should be cleaned regularly removing dust and dirt to avoid:

• carburettor malfunction

• starting problems

• reduced engine power

• unnecessary wear to engine parts

• abnormal fuel consumption

Clean the filter after every 25 hours or more regularly if operating conditions are

The condition of the spark plug is affected by:

•An incorrect carburettor setting.

•An incorrect fuel mixture (too much or faulty oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties.

0,5 mm

exceptionally dusty.

Cleaning the air filter Dismantle the air filter cover and remove the air filter. Wash in clean, warm soapy water. Ensure that the

filter is dry before refitting. An air filter used for a long period of time can never be cleaned completely. Therefore it is necessary to replace the filter from time to time with a new filter. A damaged air filter must always be replaced.

Angle gear

The angle gear is filled with a sufficient quantity of grease at the factory. However, before using the machine you should check that the angle gear is filled to 3/4 with grease. Use HUSQVARNA special grease.

Normally, the grease does not need to be changed except when the angle gear is repaired.

Two-part shaft

The end of the drive axle in the lower shaft should be lubricated with grease every 30 hours. There is a risk that the drive axle ends (splined coupling) on two-part shafts jam if they are not lubricated regularly.

If the machine is low on power, difficult to start or runs poorly while idling always check the spark plug first.

If the spark plug is dirty, clean it and at the same time check that the electrode gap is 0.5 mm. The spark plug should be changed after about one month of operation or earlier if necessary.

NOTE! Always use the recommended type of spark plug. An incorrect spark plug can damage the cylinder/piston.

Filing the grass blade

!WARNING!

Always stop the engine before you start work on any part of the blade. The blade continues to rotate even after the throttle has been released. Ensure that the blade has stopped completely and remove the cable from the spark plug before you start to work with it.

•See the cutting

equipment’s packaging for correct filing instructions.

• The blades are sharpened using a single cut flat file.

• Sharpen all edges equally to maintain the balance of the blade.

!WARNING!

Always discard a blade that is bent, twisted, cracked, shattered or damaged in any other way. Never attempt to straighten a twisted blade for use again. Only use original blades of the prescribed type.

26 – English

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 225R/RD/RJ 232R/RD 235R 101 89Max 10000 rpm Symbol ExplanationSymbols Contents Personal protective equipment Safety InstructionsMachine‘s safety equipment Cutting Equipment1 Anti-vibration systemQuick-release Muffler Locking nutVibration damping system Cutting equipment Quick-releaseFiling the grass blade Cutting equipmentSharpening the clearing blade Trimmer headStart General safety instructionsFuel safety Transport and storageBasic safety precautions General working instructionsDesignations Adjusting the harness and clearing sawBasic clearing techniques Working methods Forestry clearing using a saw bladeClearing‘s ABC Brush cutting using the saw blade Brush cutting using a grass bladeTrimming Grass trimming using the trimmer headClearing SweepingWhat is WHAT? What is what on the brush cutter?Assembly Assembling the handlebars 235RAssembling the J-handlebars 225RJ Transport position, handlebars and J-handlebarsAssembling the blade guard and grass blade Assembling other guards and cutting equipment Assembling the spray guard and trimmer head Trimmy SII 235RDismantling Adjusting the harness and clearing sawAssembling Fuelling Fuel HandlingFuel mixture Start and stop Start and StopControl before starting Maintenance CarburettorHigh speed needle Final setting of the idling speed TCorrectly adjusted carburettor Muffler Cooling systemTwo-part shaft Air filter Spark plugAngle gear Filing the grass bladeWeekly maintenance Maintenance scheduleDaily maintenance Monthly maintenanceTechnical Data Technical data 225RJ 225R/RD 232R/RD 235RType Cutting attachment Guard Art No Approved accessories 232R/RD Type Cutting attachmentApproved accessories 235R Type Cutting attachment Guard Ref No«*2o5¬

232R, 235R, 235FR, 225R, 225RD, 225RJ, 232R, 232RD, 235R specifications

Husqvarna, renowned for its expertise in outdoor power equipment, offers a range of robust strimmers that cater to both professional and homeowner needs. Among these are the models 225R, 225RD, 225RJ, 232R, 232RD, 235R, and 235FR. Each of these strimmers boasts unique features, advanced technologies, and characteristics that make them stand out in the competitive landscape.

The Husqvarna 225R is designed for residential use, featuring a lightweight design that ensures ease of maneuverability. Its Smart Start technology allows for quick starting with minimal resistance, making it user-friendly for amateurs and seasoned users alike. The model is powered by a reliable two-stroke engine which strikes an optimal balance between power and fuel efficiency.

The 225RD variant adds versatility with its dual-line cutting system, perfect for tackling thicker grass and weeds. This model also integrates an ergonomic handle, reducing fatigue during extended use and enhancing overall comfort.

Moving on, the 225RJ version is equipped with an adjustable cutting width, allowing users to adapt to various tasks. The reinforced trimmer head ensures durability while the low emissions technology adheres to environmental standards, making it a sustainable choice for the eco-conscious consumer.

The Husqvarna 232R builds on the strengths of its predecessor with increased power output, making it suitable for demanding landscaping tasks. Its robust build quality and sturdy materials enable it to withstand rigorous use, catering perfectly to landscaping professionals.

The 232RD model features a heavier-duty cutting head that facilitates tough weed clearance, ideal for larger properties. Additionally, it maintains a comfortable grip, aiding precision in operation.

The 235R introduces improved fuel efficiency, reducing the environmental impact without sacrificing performance. The easy-to-adjust harness and balance system distribute weight evenly, allowing for prolonged use without discomfort.

Lastly, the 235FR is designed for commercial use, featuring a high-capacity engine that maximizes output efficiency. The frame design allows for operation on steep terrains, ensuring versatility in applications, while the anti-vibration technology minimizes strain on the user’s hands, making long hours of operation more bearable.

In summary, Husqvarna’s lineup of strimmers — the 225R, 225RD, 225RJ, 232R, 232RD, 235R, and 235FR — represents an excellent amalgamation of power, user comfort, and eco-friendliness. Each model is tailored to meet specific needs, whether for homeowners or professionals, ensuring that superior cutting performance and reliability remain at the forefront of outdoor maintenance tasks.
Top Page Image Contents