Husqvarna 11R Introduction, Dear Customer, Driving and transport on public roads, Towing, Use

Page 3

INTRODUCTION

Dear Customer,

Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine.

We hope you will find this operator’s manual very useful. By following its instructions (on operation, service, maintenance, etc.) you will significantly extend the life of the machine and even its second-hand value.

When you sell your Rider, make sure you pass on the operator’s manual to the new owner.

The last chapter in the operator’s manual consists of a Service Journal. Make sure that all service work and repairs are recorded. A well-documented service history reduces the costs of seasonal maintenance and influences the second-hand value of the machine. Bring the operator’s manual with the Rider when bringing it to a workshop for service procedures.

Driving and transport on public roads

Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held.

Towing

When your machine is equipped with a hydrostatic transmission you should only tow the machine over short distances and at a low speed, otherwise there is a risk of damaging the transmission.

The power transmission must be disengaged when towing, see the instructions under the heading Clutch control.

Use

This machine is designed to mow grass on open and level ground surfaces. In addition, there is a number of accessories recommended by the manufacturer that broadens the application area. Please contact your dealer for more information about which accessories are available. The machine may only be used with the equipment recommended by the manufacturer. All other types of use are incorrect. Use in any other way is considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer also constitute essential elements of the intended use.

This machine should be operated, serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognised regulations on safety and occupational medicine, and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury.

English – 3

Image 3
Contents Rider 11 R Rider 11 C Rider 13 C Rider 16 C AWD Contents Towing IntroductionDear Customer Driving and transport on public roadsSerial Number Good serviceService journal Pre-delivery serviceAfter the first 8 hours Symbols KEY to SymbolsKEY to Symbols General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Location of the controls What is WHAT?Presentation PresentationSeat Cutting height adjustment leverCutting unit Lifting lever for the cutting unitClutch control, front axle Release lever Rider 13 C, Rider 16 CRelease lever Rider 16 AWD Clutch control, rear axleDriving Before startingStart the engine Starting the engine with a weak battery Connecting the jump leadsRemove the cables in the reverse order Driving the Rider For Rider 13 C, Rider 16 AWD and Rider 16 CFor Rider 11 R and Rider 11 C Cutting tips Stop the engineOther objects which can be thrown out by the blades Maintenance Maintenance schedule200 Removing of the machine hoods CleaningChecking and adjusting the steering wires Adjusting the brake Rider 11R and Rider 11 CChecking the brake Rider 11 R and Rider 11 C Result in reduced braking ability Adjusting the parking brake Rider 13 C, Rider 16 CAdjusting the parking brake Rider Adjusting the throttle wireReplacing the air filter Checking the tyre pressure Replacement of fuel filterControlling the acid level in a dry- charged battery Checking the fuel pump’s air filterIgnition system FusesReplacing the spark plug Check the safety system Rider 16 AWD When the engine is running. Mind your fingers Checking the engine’s cooling air intakeChecking the cutting unit’s parallelism Adjusting the parallelism of the cutting unit Service position for the cutting unitPlacing in the service position Restoring from service position Rider 11 R Checking the bladesRemoving the BioClip plug Rider 11 C, 13 C, 16 C, 16 AWDLubrication Checking the engine’s oil levelReplacing the engine oil Rider 16 AWD Lubricating the belt adjusterLubrication Rider 11 R and Rider General lubricationProblem Procedure Troubleshooting scheduleGuard ServiceStorage Winter storageTechnical Data Rider 13 C Rider 16 AWD Rider 16 C EC-declaration of conformity Applies to Europe only Page ´z+S!¶6¶¨ Page 1151019-26

11C, 11R, 16C, 16CAWD, 13C specifications

Husqvarna is a globally renowned brand known for its expertise in outdoor power equipment, and their range of ride-on mowers showcases a blend of innovation, performance, and durability. Five standout models in their lineup—Husqvarna 11C, 16CAWD, 13C, 11R, and 16C—deliver exceptional mowing experiences with unique features and technologies.

The Husqvarna 11C is an agile, compact riding mower designed for homeowners with smaller lawns. Its efficient cutting deck allows for precise mowing even in tight spaces, while the robust engine provides reliable power. The intuitive user interface includes easy-to-reach controls, making it suitable for all gardening enthusiasts.

Next in the lineup is the Husqvarna 16CAWD, which caters to those who experience diverse terrain. This all-wheel-drive mower boasts enhanced traction, ensuring stability and maneuverability on hills and uneven surfaces. Its powerful engine and reinforced cutting deck make it a versatile choice for tackling different types of grass and landscape challenges.

The Husqvarna 13C stands out for its combination of efficiency and advanced technology. Featuring an automatic cutting height adjustment system, it adapts seamlessly to varying grass lengths. With its easy-to-use steering and ergonomic seat, the 13C prioritizes user comfort during extended mowing sessions.

The Husqvarna 11R presents a reliable option for residential users seeking a simple yet effective mowing solution. This model combines a sturdy design with efficient cutting technology, ensuring a clean finish on any lawn. Its low-profile design allows for easy access under trees and decorative fixtures, making it a practical choice for meticulous gardeners.

Lastly, the Husqvarna 16C brings premium efficiency and performance together. This larger mower is equipped with a powerful engine capable of tackling expansive lawns. The exceptional cutting deck design allows for a wider mowing path, reducing the time spent on lawn maintenance. Additionally, its innovative grass collection system enhances the mowing experience by preventing clumping and ensuring a pristine appearance.

In summary, the Husqvarna 11C, 16CAWD, 13C, 11R, and 16C models represent the forefront of ride-on mower technology, each tailored to meet distinct needs. With features such as advanced traction, ergonomic design, and user-friendly controls, Husqvarna continues to set standards in the lawn care industry, making each mowing experience not only efficient but enjoyable. Whether you have a small urban garden or a sprawling landscape, Husqvarna mowers offer the perfect solution for every mowing challenge.