Husqvarna 155 manual Storage, Winter storage, Cover, Service

Page 46

STORAGE

Winter storage

At the end of the season the machine should immediately be put in order for storage, also if it is going to stand idle for more than 30 days. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine.

Fuel stabiliser is an acceptable alternative to avoid tacky deposits during storage. If alkylate petrol (Aspen) is used stabiliser is not necessary since this fuel is stable. However, one should avoid changing from standard to alkylate petrol since sensitive rubber parts can harden. Add stabiliser to the fuel in the tank or the storage container. Always use the mixing ratios indicated by the manufacturer. Run the engine for at least 10 minutes after adding the stabiliser so that it will reach the carburettor. Do not empty the fuel tank and carburettor if stabiliser has been added.

WARNING!

Never place an engine with fuel in the tank indoors or in poorly ventilated areas where petrol fumes can come into contact with naked flames, sparks or pilot flames in boilers, hot water heaters, or drying cabinets, etc. It is highly inflammable and negligent usage can cause severe person injury

and material damage. Drain off the fuel in an approved container outdoors and well clear of naked flames. Never use petrol for cleaning purposes. Use degrea- sing agents and hot water instead.

To put the machine in order for storage follow these instructions:

1.Carefully clean the machine, especially under the cutting unit. Touch-up paint damage to avoid rust.

2.Inspect the machine for worn or damaged parts and tighten loose screws and nuts.

3.Change the oil, and take care of the waste oil.

4.Empty the fuel tank. Start the engine and run it until the carburettor is emptied of fuel.

5.Remove the spark plug and pour about a tablespoon of engine oil in the cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plug.

6.Grease all grease nipples, joints and axles.

7.Remove the battery. Clean it, charge it, and store it in a cool place.

8.Store the machine in a clean and dry place and cover it for extra protection.

Cover

There is a cover to protect your machine during storage or transport. Contact your dealer for a demonstration.

Service

When ordering spare parts, always state the purchase year, model, type, and serial number.

Always use genuine parts.

Annual inspection or trimming by an authorised service workshop is a good way of getting the best out of your machine the next season.

6017-213

44 – English

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Rider Page Contents II. Slope operation Safe operation practices for ride-on mowersGeneral operation III. ChildrenTowing IV. ServiceTravel and transport on public roads Intended useTravel and transport on public roads IntroductionDear customer TowingSerial number Safety InstructionsGood service Engine TransmissionExplanation of Symbols Starting InstructionPlacards Safety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Speed limiter Throttle and Choke leverParking brake Cutting unit Lift lever for the cutting unitSeat Lever for adjustment of cutting heightFuelling Starting the engine DrivingBefore starting Cold engineWarm engine Driving the machine Cutting tips Stopping the engine Release leverDaily Maintenance interval MaintenanceMaintenance schedule HoursFront hood Dismantling of the machine hoodsEngine hood Right-hand fenderChecking and adjustment of the steering wires Adjusting the parking brakeAdjusting the throttle wire Inspecting the mufflerReplacement of the fuel filter Replacing the air filterCheck the level of the battery acid Procedures on contact with acidIgnition system Fitting the wrong spark plug type can damage the engineChecking the safety system Checking the tyre pressure Main fuseCheck the engine’s cooling air intake Fitting the cutting unit Observe caution to avoid trapping your handInstalling BioClip Checking the cutting unit’s parallelismAdjusting the parallelism of the cutting unit Removing the cutting unitBelt replacement on BioClip Replacing the cutting unit beltsService position for the cutting unit Placing in service position6017-221 6017-222 8009-122 6017-223 Restoring from service position Checking the blades Replacing the break-pin BioClip Removal of BioClip plug CombiCheck the engine’s oil level LubricationChanging the oil Check the transmission’s oil level Lubricating the belt adjusterChange of oil filter General lubricationTrouble Shooting Schedule Problem ProcedureWinter storage ServiceStorage CoverTechnical Data Technical Data After first 5 hours ServicejournalPre-delivery service Work done Date, mileage, stamp, sign´z+H-¶5-¨ English 114 01

155 specifications

The Husqvarna 155 is a standout in the realm of modern lawn care equipment, combining robust performance with innovative technology to meet the needs of both residential and commercial users. A powerful machine designed for efficiency, the Husqvarna 155 is ideal for maintaining medium to large yards, providing an exceptional balance of maneuverability and cutting capability.

One of the most notable features of the Husqvarna 155 is its powerful engine. Equipped with a reliable and efficient gasoline engine, this machine offers impressive horsepower and torque, ensuring that it can handle dense grass and uneven terrain with ease. Furthermore, the engine is designed to reduce fuel consumption and emissions, adhering to modern ecological standards while maintaining high performance.

The cutting deck of the Husqvarna 155 is another highlight. Constructed with high-quality steel for durability, the cutting deck provides a precise and clean cut. The deck size typically ranges from 42 to 54 inches, allowing the mower to cover a large area quickly. Moreover, the adjustable cutting height feature gives users the flexibility to tailor the grass length according to their preferences or the seasonal needs of their lawn.

Husqvarna also integrates advanced technologies into the 155 model. The inclusion of Smart Start technology simplifies the starting process, reducing resistance in the starter cord for effortless ignition. This means less strain on the user and quick access to mowing, even for those less familiar with garden equipment.

Another key characteristic is the ergonomic design of the mower. The handle is adjustable, accommodating various user heights, and it features comfortable grips that reduce vibration during operation. This user-centered approach extends to the overall layout of the controls, making them intuitive and easy to access, thus enhancing the mowing experience.

Additionally, the Husqvarna 155 is built with durability in mind. Its robust frame and high-quality components ensure longevity, even under heavy use. Regular maintenance is straightforward, guided by Husqvarna’s reliable support and easy-to-follow manuals.

In summary, the Husqvarna 155 provides a perfect blend of power, efficiency, and user-friendly features. Its engine performance, intelligent technology, durable construction, and ergonomic design make it an excellent choice for anyone looking to invest in a reliable lawn mower that delivers outstanding results in lawn care. For both homeowners and professionals, the Husqvarna 155 is poised to meet and exceed expectations season after season.
Top Page Image Contents