Husqvarna 550XP Working Techniques, Before use, General working instructions, Basic safety rules

Page 22

WORKING TECHNIQUES

Before use:

6, 8

1Check that the chain brake works correctly and is not damaged.

2Check that the rear right hand guard is not damaged.

3Check that the throttle lockout works correctly and is not damaged.

4Check that the stop switch works correctly and is not damaged.

5Check that all handles are free from oil.

6Check that the anti vibration system works and is not damaged.

7Check that the muffler is securely attached and not damaged.

8Check that all parts of the chain saw are tightened correctly and that they are not damaged or missing.

9Check that the chain catcher is in place and not damaged.

10Check the chain tension.

General working instructions

IMPORTANT!

This section describes basic safety rules for using a chain saw. This information is never a substitute for professional skills and experience. If you get into a situation where you feel unsafe, stop and seek expert advice. Contact your chain saw dealer, service agent or an experienced chain saw user. Do not attempt any task that you feel unsure of!

Before using a chain saw you must understand the effects of kickback and how to avoid them. See instructions under the heading How to avoid kickback.

Before using a chain saw you must understand the difference between cutting with the top and bottom edges of the bar. See instructions under the headings How to avoid kickback and Machine’s safety equipment.

Wear personal protective equipment. See instructions under the heading ”Personal protective equipment”.

Basic safety rules

1 Look around you:

To ensure that people, animals or other things cannot affect your control of the machine.

To make sure that none of the above might come within reach of your saw or be injured by falling trees.

CAUTION! Follow the instructions above, but do not use a chain saw in a situation where you cannot call for help in case of an accident.

2Do not use the machine in bad weather, such as dense fog, heavy rain, strong wind, intense cold, etc. Working in bad weather is tiring and often brings added risks, such as icy ground, unpredictable felling direction, etc.

3Take great care when removing small branches and avoid cutting bushes (i.e. cutting many small branches at the same time). Small branches can be grabbed by the chain and thrown back at you, causing serious injury.

4Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground.

5Take great care when cutting a tree that is in tension. A tree that is in tension may spring back to its normal position before or after being cut. If you position yourself incorrectly or make the cut in the wrong place the tree may hit you or the machine and cause you to lose control. Both situations can cause serious personal injury.

6Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance.

7When you put the chain saw on the ground, lock the saw chain using the chain brake and ensure you have a constant view of the machine. Switch the engine off before leaving your chain saw for any length of time.

WARNING! Sometimes chips get stuck in

! the clutch cover causing the chain to jam. Always stop the engine before cleaning.

General rules

1If you understand what kickback is and how it happens then you can reduce or eliminate the element of surprise. By being prepared you reduce the risk. Kickback is usually quite mild, but it can sometimes be very sudden and violent.

2Always hold the chain saw firmly with your right hand on the rear handle and your left hand on the front handle. Wrap your fingers and thumbs around the handles. You should use this grip whether you are

22 – English

Image 22
Contents Operator′s manual Symbols on the machine KEY to SymbolsDecompression valve Symbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge setting Lubricating cutting equipment Adjustment of depth gauge settingTensioning the chain Cause serious or even fatal injuryChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubricationChecking wear on cutting equipment Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting Starting and StoppingStarting and stopping Cold engineStopping Before use Basic safety rulesWorking Techniques General working instructionsWorking Techniques Terms Basic cutting techniqueLimbing Safe distance Tree felling techniqueFelling direction Felling Training we advise you not to fell trees Clearing the trunk and preparing your retreatFelling cut Your sawFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburettor adjustment MaintenanceGeneral Checking the brake trigger Checking the inertia brake releaseImmediately Muffler Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil spring Air filterSpark plug Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpRunning when making adjustments Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature 0C or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data550XP TrioBrake 550XPG Guide bar and chain combinations Saw chain filing and file gaugesApplies to Europe only EC-declaration of conformityEN ISO 12100-2/A12009, Cispr 122007, EN ISO Page Page