Husqvarna 550XPG, 545 Filling with chain oil, Checking chain lubrication, Chain drive sprocket

Page 15

GENERAL SAFETY PRECAUTIONS

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

Check that the oil channel in the bar is not obstructed. Clean if necessary.

Check that the groove in the edge of the bar is clean. Clean if necessary.

Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary.

If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your service agent.

Chain drive sprocket

The clutch drum is fitted with one of the following drive sprockets:

ASpur sprocket (the chain sprocket is welded on the drum)

BRim sprocket (replaceable)

AB

Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain.

Needle bearing lubrication

Both versions of sprockets have a needle bearing on the drive shaft, which has to be greased regularly (once a week). CAUTION! Use a high-quality bearing grease or engine oil.

English 15

Image 15
Contents Operator′s manual KEY to Symbols Symbols on the machineDecompression valve Symbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge setting Cause serious or even fatal injury Adjustment of depth gauge settingTensioning the chain Lubricating cutting equipmentNeedle bearing lubrication Filling with chain oilChecking chain lubrication Chain drive sprocketChecking wear on cutting equipment Working with the chain AssemblyFitting the bar and chain Fitting a spike bumperFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageCold engine Starting and StoppingStarting and stopping StartingStopping General working instructions Basic safety rulesWorking Techniques Before useWorking Techniques Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Your saw Clearing the trunk and preparing your retreatFelling cut Felling Training we advise you not to fell treesCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentGeneral Checking the inertia brake release Checking the brake triggerImmediately Muffler Starter Changing a broken or worn starter cordTensioning the recoil spring Fitting the starter Air filterSpark plug Changing a broken recoil springNeedle bearing lubrication Adjustment of the oil pumpRunning when making adjustments Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningTemperature 0C or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data550XP TrioBrake 550XPG Saw chain filing and file gauges Guide bar and chain combinationsEC-declaration of conformity Applies to Europe onlyEN ISO 12100-2/A12009, Cispr 122007, EN ISO Page Page