Husqvarna 1153181-95 Heated handles, Fitting the winterising kit, Temperature 0C 32F or colder

Page 37

MAINTENANCE

Fitting the winterising kit

Cut out a hole using a knife as shown.

Fit the winter cover in the cylinder cover.

THIS SIDE

VISIBLE

537 21 05 XX

Temperature 0°C (32°F) or colder:

Move the cover from position A to position B so that preheated air from the cylinder can pass into the carburettor compartment and prevent, e.g. the air ﬁlter icing up again. When ﬁtting the winter cover in position B the centrifugal cleaning nozzle is blocked. This measure requires the air ﬁlter to be cleaned more regularly.

Temperature -5°C (23°F) or colder:

For running the machine in cold weather or powder snow, a special cover is available, which is mounted on the starter housing. This reduces the intake of cold air and prevents large amounts of snow from being sucked in.

A

B

C

CAUTION! If the special winterising kit has been ﬁtted or any measures have been taken to increase the temperature these changes must be reversed before the machine is used in normal temperature conditions. Otherwise there is a risk of overheating, resulting in severe damage to the engine.

IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer).

Heated handles

576 XPG

On models with the model code XPG both the front handle bar and the rear handle are equipped with electrical heating coils. These are supplied with electricity from a generator built into the chain saw.

Electrical carburetor heating

576 XPG

If this chain saw has the model code XPG then it is equipped with an electrically heated carburettor. The electrical heating prevents icing in the carburettor. A thermostat regulates heating so that the carburettor always has the correct working temperature.

English – 37

Image 37

Contents 570 576 XP 576 XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufﬂerBar Cutting equipment designed to reduce kickbackChain General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Tree felling techniqueLog is supported at one end. There is a high risk Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral When the bar hits the stump the brake should be applied Correctly adjusted carburetorChecking brake band wear Checking the front hand guardImmediately Checking the brake triggerStarter MufﬂerChanging a broken or worn starter cord Tensioning the recoil spring Air ﬁlterChanging a broken recoil spring Fitting the starterLubricating the bar tip sprocket Spark plugNeedle bearing lubrication Must always be replacedAir Injection centrifugal cleaning Adjustment of the oil pumpWhen making adjustments Cooling systemTemperature -5C 23F or colder Temperature 0C 32F or colderHeated handles Fitting the winterising kitDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain ﬁling and ﬁle gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Safety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsOriginal instructions 1153181-95